Why Your 2020 KTM 1290 Super Duke GT Is Using More Fuel Than It Should

Shop parts for a 2020 KTM 1290 Super Duke GT Motorcycle.

The 2020 KTM 1290 Super Duke GT is a liquid-cooled, fuel-injected four-stroke V-twin with chain final drive, built to cover distance quickly with luggage and a passenger aboard. It was never going to be a sipper, but it should be consistent. When you find yourself stopping for fuel more often than you used to, something has changed — and most of the likely causes are diagnosable without a shop visit.

First, Make Sure the Change Is Real

Before chasing a fault, measure properly. Fill to the same level each time, reset the trip meter or note the odometer reading, ride normally, then refill and divide the miles ridden by the fuel it took to refill. Do this over several tanks rather than one. A single tank can be skewed by a stiff headwind, a lot of stop-and-go traffic, or a fill-up that stopped at a different level than the last one.

It is also worth checking whether your odometer is telling the truth. Changing sprocket sizes on a chain-driven machine, or fitting tires with a different diameter or profile than stock, throws off the speedometer and odometer. A shorter final drive ratio genuinely costs fuel because the engine turns more revs for the same road speed, and it also makes the odometer over-report distance. Both effects can make your calculated economy look worse than the bike is actually doing.

Riding Conditions and Habits That Quietly Cost Fuel

Cold weather thickens oil, lengthens warm-up time, and raises rolling resistance, and many regions switch to a winter fuel blend that simply carries less energy per gallon. Ethanol-blended fuel has a similar effect. Add a headwind, a passenger, loaded panniers, or a long stretch of sustained highway speed, and consumption climbs.

Rider behavior matters just as much. Short trips that never let the engine reach full operating temperature are the worst case, because the fuel injection system deliberately runs richer while the engine is cold. Long idling warm-ups burn fuel while covering zero miles. Aggressive throttle use on a big V-twin is expensive, and a sharper ride mode encourages exactly that. Try several tanks ridden deliberately gently in a milder mode before assuming something is broken.

Rolling Resistance, Brakes, and the Chain

Underinflated tires are the most common and most overlooked cause of poor fuel economy on any motorcycle. Check pressures when the tires are cold and set them to the specification for your load. A tire that is several pounds low will feel vague and cost you fuel on every mile.

A dragging brake is next on the list. A caliper with sticky pistons or a corroded slide can hold the pads against the rotor, and the drag is often subtle enough that you notice heat and reduced economy long before you notice anything through the lever. After a normal ride, carefully feel the rotors — if one is noticeably hotter than the others, that corner is dragging.

Then there is the chain. A dry, rusty, or overtightened chain robs power and loads the countershaft bearing. Clean it, lubricate it, and set the slack to specification. A chain that is too tight is worse than one that is slightly loose.

Air Intake and Spark Quality

An engine needs the right mix of air, fuel, and spark. A clogged or heavily oiled air filter restricts airflow, and the engine management system compensates in ways that hurt efficiency. If you ride in dusty conditions or have never replaced the filter, this is a cheap place to start.

Spark plugs matter too. Plugs that are worn, fouled, or gapped incorrectly can fail to ignite the mixture cleanly, which wastes fuel and shows up as rough running. This bike uses a fully electronic ignition, so there are no points to wear or adjust — the ignition side of the equation comes down to plug condition and the sensors feeding the ECU.

Fuel Injection and Sensor Problems

On a fuel-injected machine like the 1290 Super Duke GT, the engine management system decides how much fuel to deliver based on sensor input. If a sensor lies to it, the mixture goes rich and economy suffers. An oxygen sensor that has drifted or failed is a classic culprit, since it is the component that tells the ECU whether the mixture is correct in the first place.

An engine coolant temperature sensor that reads colder than reality is another one. The ECU believes the engine is still warming up, so it holds a richer mixture far longer than necessary. A leaking or dirty injector can also deliver more fuel than commanded, or deliver it in a poor spray pattern that does not burn completely.

On a V-twin with more than one throttle body, synchronization matters as well — if the cylinders are not pulling evenly, the ECU is making fueling decisions from an uneven picture. Stored fault codes are worth reading even if no warning light is showing, and any raw fuel smell around the bike should be tracked down immediately, whether it comes from a hose, a fitting, or the tank area.

Engine Condition, Cooling, and Modifications

As mileage accumulates, compression can fall off through normal wear, and an engine that seals poorly converts less of its fuel into forward motion. Valve clearance that has drifted out of specification is one contributor worth having checked on schedule, since it affects how well the cylinders fill and seal.

Because this bike is liquid-cooled, the thermostat deserves a mention. A thermostat stuck open keeps the engine from reaching full operating temperature, and a cold engine is a thirsty engine. If the temperature display never seems to come up to normal, that is a clue worth following.

Modifications are the last big category. An aftermarket exhaust or high-flow air filter installed without matching fuel injection tuning can leave the mixture richer than the engine needs. If your mileage dropped right after a performance part went on, the two are almost certainly related.

When to Hand the Bike to a Mechanic

Some symptoms point to something beyond a simple check. A strong fuel smell, black smoke from the exhaust, spark plugs that come out sooty, a warning light on the dash, or rough running alongside the mileage drop all suggest the bike needs proper diagnosis rather than guesswork. The same is true if you have already checked tire pressures, the chain, the air filter, and your own riding habits, and the economy is still worse than it used to be.

Describe what you have observed: when the change started, whether it came on suddenly or gradually, how the bike runs otherwise, and what you have already checked. That information shortens the diagnostic process considerably and helps ensure the fix addresses the real cause rather than a symptom.

Related Shopping Categories

Shop Fuel System Parts for a 2020 KTM 1290 Super Duke GT Motorcycle.

Shop Air Filters for a 2020 KTM 1290 Super Duke GT Motorcycle.

Shop Tires for a 2020 KTM 1290 Super Duke GT Motorcycle.

Shop Brake Parts for a 2020 KTM 1290 Super Duke GT Motorcycle.

Shop Spark Plugs for a 2020 KTM 1290 Super Duke GT Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.