What Oil Does a 2020 Sherco 300 SE Factory Take? Two-Stroke Lubrication Explained
Shop parts for a 2020 Sherco 300 SE FACTORY Dirt Bike.
The 2020 Sherco 300 SE Factory is a two-stroke enduro machine, and that single fact shapes every oil decision you will make on it. Unlike a four-stroke, where one sump of engine oil handles the whole job, a two-stroke splits lubrication into two completely separate systems that never share fluid. Getting both right is what keeps the top end crisp, the clutch consistent, and the gearbox alive through a full season of trail abuse.
Two Lubrication Systems, Two Different Jobs
On the 300 SE Factory, the engine itself has no oil sump, no oil pump circulating through the crankcase, and no oil filter in the traditional sense. Instead, the crankshaft bearings, piston, rings, and cylinder wall are lubricated by oil that arrives with the fuel charge and burns off during combustion. That oil is either pre-mixed into the gas can before you fill the tank or, on machines equipped with an oil-injection system, metered automatically from a separate reservoir. Sherco's 300 SE Factory is configured as a premix bike in its standard form, which means the rider is responsible for getting the ratio right at the pump.
The second system is the transmission. The gearbox, clutch, and primary drive sit in their own sealed case with its own oil supply, completely isolated from the combustion chamber. This oil does not burn, does not mix with fuel, and is drained and replaced on a regular service schedule. Treating these two systems as one is the most common mistake new two-stroke owners make, and it leads to either a smoked clutch or a seized top end.
Choosing the Right Two-Stroke Premix Oil
Modern two-stroke oils are almost universally synthetic or semi-synthetic, and that shift happened for good reason. Synthetic formulations resist the extreme heat of a high-revving 300cc two-stroke far better than older mineral oils, burn more completely, and leave noticeably less carbon behind on the power valve, piston crown, and exhaust port. On an enduro bike that spends long stretches at part throttle in technical terrain, that clean-burning characteristic matters as much as outright lubrication.
Look for an oil explicitly labeled for two-stroke motorcycle use and rated for premix application. Products carrying a JASO FD or ISO-L-EGD rating represent the current high-detergent standard and are a sound choice for a bike like this. Avoid anything marketed for outboard motors, chainsaws, or general-purpose small engines — those formulations are designed for cooler, lower-stress operation and do not hold up in a liquid-cooled performance engine. If your particular 300 SE Factory is fitted with an oil-injection system rather than running premix, use an injection-specific two-stroke oil and never substitute a premix-only product, since the two behave differently in a metering pump.
Premix Ratios: What Is Typical and Why It Matters
Across the two-stroke dirt bike world, premix ratios generally land somewhere between 32:1 and 50:1, with 40:1 and 50:1 being the most commonly cited figures on modern enduro and motocross machines. The exact number your engine wants depends on the oil you choose and the manufacturer's recommendation, so confirm the figure for your specific bike before you mix your first can.
Ratio errors cut both ways. Mixing too lean on oil — say, running 60:1 when the engine wants 40:1 — reduces the film of lubrication reaching the piston skirt and crank bearings, and the damage shows up fast under load. Mixing too rich, on the other hand, fouls spark plugs, gums up the power valve, loads the exhaust with unburned residue, and actually leans out the air-fuel mixture because oil displaces fuel in the same volume of premix. Neither direction is a small deal on a 300cc two-stroke that makes its power high in the rev range.
Measure with a proper ratio cup or a graduated container rather than eyeballing it. A few milliliters of error per gallon adds up over a long ride, and consistency is what keeps jetting predictable.
Gearbox Oil for the 300 SE Factory
The transmission side of the equation is more familiar territory. Most two-stroke dirt bikes, including enduro models in this displacement class, run a motorcycle-specific gear oil in the 10W-30 or 10W-40 range, and many riders find that a dedicated transmission fluid designed for wet-clutch applications gives the smoothest, most consistent clutch feel. Because the clutch plates sit in the same oil bath as the gears, the fluid has to do double duty: protect gear teeth under shock loads and allow the clutch to engage and disengage without grabbing or slipping.
That is why automotive engine oil is a poor choice here. Many modern car oils contain friction modifiers designed to reduce drag, and those additives are exactly what you do not want on wet clutch plates. A JASO MA or MA2 rated motorcycle oil avoids the problem entirely. Synthetic gear oil offers better shear stability when the clutch is worked hard on long, technical descents, while a quality conventional motorcycle oil remains a perfectly serviceable and more affordable option for most riders.
What Goes Wrong With the Wrong Oil
Running a low-quality or incorrectly rated premix oil typically shows up first as heavy carbon deposits on the power valve, which gradually robs the engine of its low-end snap and eventually causes the valve to stick. Spark plug fouling follows, along with a persistent spooge drip from the silencer joint. Over time, inadequate lubrication accelerates piston and ring wear, and a top end that should last a full season may need attention in half that time.
On the gearbox side, the symptoms are different but equally clear. Friction-modified oil causes the clutch to slip under hard acceleration, and the slipping generates heat that degrades the oil further. Too heavy a gear oil in cold conditions makes the clutch drag and the shift action notchy. Both problems are avoidable with a single correct choice at the counter.
Confirming the Exact Specification for Your Bike
The guidance above reflects what is typical and widely accepted for two-stroke enduro bikes in this class, and it will serve you well in practice. For the precise premix ratio, the recommended premix oil type, and the exact gearbox oil viscosity and fill quantity for your 2020 Sherco 300 SE Factory, a quick check of the owner's manual or a call to your dealer settles it in a minute or two. That confirmation step is worth doing once, then you can mix and change with confidence for the life of the bike.
Related Shopping Categories
Shop Oils and Fluids for a 2020 Sherco 300 SE FACTORY Dirt Bike.
Shop Oil for a 2020 Sherco 300 SE FACTORY Dirt Bike.
Shop Air Filters and Oil for a 2020 Sherco 300 SE FACTORY Dirt Bike.
Shop Transmission for a 2020 Sherco 300 SE FACTORY Dirt Bike.
Shop Oil Filters for a 2020 Sherco 300 SE FACTORY Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.