What Oil Does a 2019 Sherco 300 SE Factory Take? Premix and Gearbox Guidance
Shop parts for a 2019 Sherco 300 SE FACTORY Dirt Bike.
The 2019 Sherco 300 SE Factory is a two-stroke enduro machine, and that single fact shapes every oil decision you will make on it. Unlike a four-stroke, where one sump of engine oil handles the whole job, this bike splits lubrication into two completely separate systems that never share fluid. Getting both right is what keeps the top end clean, the clutch consistent, and the gearbox alive through seasons of hard off-road use. This guide walks through what each system needs, what weights and types are typical for a bike in this class, and where to confirm the final numbers for your specific machine.
Two Independent Lubrication Systems on the 300 SE Factory
The first system lives inside the combustion process. On a two-stroke like the 300 SE Factory, the crankcase does not hold a reservoir of oil for the engine itself. Instead, lubricant is introduced into the intake charge, either by being pre-mixed into the fuel can before you fill the tank or by an oil-injection pump that meters it automatically. That oil travels through the crankcase, coats the cylinder wall, lubricates the rod and main bearings, and then burns off during combustion. It is a total-loss system by design, which is why two-strokes always consume oil and why the oil you choose has to burn cleanly.
The second system is the gearbox. The 300 SE Factory uses a wet clutch and a constant-mesh transmission that sit in their own sealed case, completely isolated from the fuel and the combustion chamber. That case holds a fixed quantity of gear oil that circulates over the clutch plates, shift forks, and gear clusters. Because the two systems never touch, the oil you pour into the transmission has nothing to do with the oil you mix into your fuel — and confusing the two is one of the more expensive mistakes a two-stroke owner can make.
Selecting a Two-Stroke Premix Oil
Modern two-stroke oils are almost universally synthetic or semi-synthetic formulations built for high-revving, high-temperature engines. The key properties to look for are clean burn characteristics, resistance to carbon and varnish buildup on the power valve and piston crown, and adequate film strength at the bearings. Oils marketed as full synthetic two-stroke racing or off-road oils generally deliver the best combination of these traits, and they are the common choice for a performance-oriented enduro bike like the 300 SE Factory.
You will see oils labeled for air-cooled engines, for water-cooled engines, and for specific applications like outboard or chainsaw use. For a liquid-cooled, power-valve-equipped enduro engine, stick with a product intended for high-performance water-cooled two-strokes. Avoid anything rated only for low-speed utility engines, and avoid automotive two-cycle additives that are not formulated for the heat and load this engine sees. A quality JASO FD or ISO-L-EGD rated oil is a reasonable benchmark to shop against.
Premix Ratios: What Is Typical and Why It Matters
If your bike runs on pre-mixed fuel, the ratio is the single most important number in this article. Common two-stroke premix ratios fall broadly between 32:1 and 50:1, with some manufacturers specifying leaner mixtures in the 60:1 to 66:1 range when a high-quality synthetic oil is used. Sherco two-strokes in this era are typically run on pre-mixed fuel rather than oil injection, so you will be measuring oil into a fuel can at every fill.
Too rich a mixture — more oil than needed — fouls spark plugs, gums up the power valve, and produces excessive carbon and spooge out the exhaust. Too lean — not enough oil — starves the rod bearing and cylinder wall, and the resulting failure usually arrives without warning. Because the correct ratio depends on both the engine design and the specific oil's formulation, confirm the figure your bike calls for rather than assuming a generic number applies.
Gearbox Oil for the 300 SE Factory
The transmission side is far more conventional. Most two-stroke dirt bikes in this displacement class specify a motorcycle-specific gear oil in a viscosity range such as 10W-30 or 10W-40, and the 300 SE Factory fits that pattern. What matters more than the exact weight is that the oil is designed for a wet clutch. Automotive engine oils frequently contain friction modifiers that let a wet clutch slip under load, which shows up as a mushy engagement and eventually as glazing and wear.
Look for a JASO MA or MA2 rating on the bottle, which indicates the oil has been tested for wet-clutch compatibility. Both conventional and synthetic gear oils work here; synthetics generally hold up better under the heat and shear that enduro riding produces, while conventional oils cost less and are perfectly serviceable for many riders. Capacity is modest, so the cost difference per change is small either way.
What Goes Wrong With the Wrong Oil
Using a car oil in the gearbox is the most common error, and it typically announces itself as clutch slip on hard acceleration out of a corner. Using a low-grade premix oil or running the mixture too lean shows up differently: detonation, a scored piston, or a seized rod bearing. Running the mixture too rich is less catastrophic but still costly over time, since carbon deposits on the power valve rob the engine of the crisp low-end response this bike is known for, and fouled plugs turn a trailside stop into a push back to the truck.
There is also a subtler issue with mixing oil brands and types between changes. Different additive packages can behave unpredictably together, so once you settle on a gear oil that gives clean clutch feel, staying with it is the simpler path.
Confirming the Exact Specification for Your Bike
The guidance above reflects what is typical and widely used for a 2019 Sherco 300 SE Factory, and it will get you riding confidently. For the precise premix ratio, the exact gearbox oil viscosity, and the fill quantity, your owner's manual is the authoritative source, and a Sherco dealer can confirm the same details in a minute or two. Treat that as a quick verification step rather than a hurdle — check the numbers once, write them on the wall of your garage, and every oil decision after that becomes automatic.
Related Shopping Categories
Shop Oils and Fluids for a 2019 Sherco 300 SE FACTORY Dirt Bike.
Shop Oil for a 2019 Sherco 300 SE FACTORY Dirt Bike.
Shop Air Filters and Oil for a 2019 Sherco 300 SE FACTORY Dirt Bike.
Shop Transmission for a 2019 Sherco 300 SE FACTORY Dirt Bike.
Shop Oil Filters for a 2019 Sherco 300 SE FACTORY Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.