Oil Guidance for the 2018 Sherco 300 SE Factory Two-Stroke

Shop parts for a 2018 Sherco 300 SE FACTORY Dirt Bike.

The 2018 Sherco 300 SE Factory is a two-stroke enduro machine, and that single fact shapes everything about how you keep it lubricated. Unlike a four-stroke, which runs one shared oil supply through the engine, clutch, and gearbox, this bike splits the job in two. One oil goes into the fuel and burns with it. A completely different oil lives in the transmission case and never touches the combustion chamber. Getting both right is what keeps a 300 SE Factory pulling hard off the bottom and holding together through long, dusty enduro loops.

Two Separate Lubrication Systems, Two Separate Oils

On the 2018 Sherco 300 SE Factory, the engine itself is lubricated by oil that is blended into the gasoline. As the fuel-and-oil mixture is drawn into the crankcase and up through the transfer ports, that oil coats the cylinder wall, the piston skirt, the ring, the small end bearing, and the main bearings before it burns off in the combustion event. There is no sump, no oil pump feeding the top end, and no filter to change on the engine side of things.

The transmission is a different story entirely. The gearbox, clutch, and primary drive sit in their own sealed case with its own oil supply, and that oil is not consumed or burned. It stays in the case, gets churned by the gears, and is drained and replaced at service intervals. Because the two systems never share fluid, you can't substitute one for the other. Premix oil in the gearbox would be wrong, and gear oil in the fuel would be catastrophic. Treat them as two independent maintenance items that happen to live on the same motorcycle.

Choosing a Two-Stroke Premix Oil

Modern two-stroke oils are almost universally synthetic or semi-synthetic, and that shift happened for good reason. A quality synthetic premix oil is formulated to burn cleanly, resist the formation of hard carbon deposits on the power valve and piston crown, and maintain a protective film under the high heat and lean conditions that a 300cc enduro engine sees. Mineral-based two-stroke oils still exist and can work in a pinch, but they tend to leave more residue and offer less margin when the bike is run hard or jetted slightly lean.

Look for an oil explicitly labeled for two-stroke motorcycle or powersports use, and pay attention to whether it's designed for premix or for oil injection. The 300 SE Factory is a premix bike, so you want a product intended to be mixed with fuel at the pump. Oils marketed for injection systems are blended differently and aren't the right choice here. Beyond that, the practical differences between reputable premix oils come down to how clean they burn and how well they hold up in a high-revving, high-compression off-road engine.

Premix Ratios: What's Typical and Why It Matters

Most two-stroke dirt bikes in this displacement class run somewhere in the 32:1 to 50:1 range, and 40:1 to 50:1 is the common territory for modern enduro two-strokes running a quality synthetic oil. The exact figure the manufacturer specifies for your bike is the one to follow, and it's worth confirming rather than assuming, because the ratio interacts with jetting, oil quality, and how the bike is ridden.

Running too rich on oil — say 20:1 when the engine wants 50:1 — leaves excess oil that doesn't fully burn, which contributes to spooge dripping from the silencer, fouled spark plugs, and carbon buildup on the power valve. Running too lean on oil starves the piston and bearings of protection, and the damage from that shows up fast. A seized piston on a 300 two-stroke is an expensive lesson in mixing discipline. Measure with a ratio cup or a graduated container rather than eyeballing it, and mix consistently every time you fill up.

Transmission and Gearbox Oil for the 300 SE Factory

The gearbox side of the 300 SE Factory takes a motorcycle-specific transmission oil, and the common viscosity range for bikes like this is 10W-30 or 10W-40. Many riders run a dedicated gear oil, while others use a JASO-rated motorcycle engine oil in the same weight, since the clutch on this bike is a wet clutch bathed in the same fluid as the gears. Either approach can work as long as the oil is formulated for wet-clutch motorcycle transmissions.

What you want to avoid is a standard automotive engine oil with friction modifiers, because those additives can cause the clutch to slip under load. A slipping clutch on a 300 two-stroke shows up as revs climbing without matching forward drive, and it gets worse as the oil breaks down. A dedicated motorcycle transmission fluid or a JASO MA-rated oil sidesteps that problem entirely. Change the gearbox oil on a regular basis — enduro use is hard on transmission fluid because of heat, clutch abuse, and the constant on-off throttle of technical riding.

What Happens When You Run the Wrong Oil

The consequences of getting the premix side wrong tend to be gradual and then sudden. Carbon accumulates on the power valve until the exhaust port timing is restricted and the bike loses its top-end pull. Spark plugs foul repeatedly, especially at low rpm in tight woods sections. In the worst case, inadequate oil film leads to piston scuffing and a seizure that ends your ride and your top end at the same time.

On the gearbox side, the failure mode is usually clutch-related rather than catastrophic. Friction-modified automotive oil causes slippage and glazing. Oil that's too thin for the conditions breaks down under heat and stops protecting the gear faces. Neither problem is dramatic at first, which is exactly why it's easy to ignore until a clutch replacement or a transmission rebuild forces the issue.

Confirming the Exact Spec for Your Bike

Everything above reflects what's typical and widely used for a 2018 Sherco 300 SE Factory and for two-stroke enduro bikes in this class generally. For the precise premix ratio and the exact gearbox oil viscosity and fill quantity, your owner's manual is the authoritative source, and a Sherco dealer can confirm it in a minute if the manual isn't handy. That's a quick check, not a reason to hold off on maintenance. Get the ratio right, use a quality synthetic premix oil, keep fresh wet-clutch-safe fluid in the gearbox, and this 300 will reward you with the crisp, torquey power delivery it was built to deliver.

Related Shopping Categories

Shop Oils and Fluids for a 2018 Sherco 300 SE FACTORY Dirt Bike.

Shop Oil for a 2018 Sherco 300 SE FACTORY Dirt Bike.

Shop Air Filters and Oil for a 2018 Sherco 300 SE FACTORY Dirt Bike.

Shop Transmission for a 2018 Sherco 300 SE FACTORY Dirt Bike.

Shop Oil Filters for a 2018 Sherco 300 SE FACTORY Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.