What Oil Does a 2013 Yamaha PW50 Take? Two-Stroke and Gearbox Lubrication Explained

Shop parts for a 2013 Yamaha PW50 Dirt Bike.

The 2013 Yamaha PW50 is a 49cc air-cooled two-stroke, and that single fact shapes every oil decision you will make for the bike. Unlike a four-stroke, where one sump of oil handles the engine, clutch, and transmission together, the PW50 splits lubrication into two entirely separate systems that never share fluid. Understanding which system you are servicing — and which oil belongs in each — is the whole game. Get that distinction right and the rest of the choices become straightforward.

Two Separate Lubrication Systems, Two Different Oils

On the PW50, the crankshaft, piston, rings, and cylinder bore are lubricated by oil that arrives with the fuel charge. That oil is consumed in the combustion process and exits through the exhaust, which is why a two-stroke always needs a continuous supply of fresh oil rather than a sump that gets drained and refilled. This is the oil that keeps the top end alive, and it is the oil most people mean when they ask what a PW50 takes.

The second system is the gearbox. The PW50 runs a single-speed automatic transmission with a wet centrifugal clutch, and that assembly sits in its own small oil bath, completely sealed off from the combustion chamber. Oil here is not burned; it stays in the case, lubricating gears and clutch plates and carrying away heat. Because the two systems are isolated, a problem with one has nothing to do with the other, and topping up the wrong one will not help anything.

There is also a third, smaller lubrication point worth knowing about: the shaft final drive at the rear wheel, which has its own tiny gear case and its own lubricant. It is easy to overlook because it holds so little fluid, but it is a genuine service item on this bike.

What Kind of Two-Stroke Oil the PW50 Wants

Yamaha equipped the PW50 with an oil injection system, so you do not pour oil into the fuel tank at the pump. Instead, a separate oil reservoir feeds a metering pump that delivers oil into the intake tract in proportion to throttle and engine speed. That design changes which two-stroke oil you should buy. Injection systems want an oil formulated to flow through small passages and mix readily with fuel at low temperatures, which is a different requirement than a premix-only racing oil designed to be dumped into a gas can at a fixed ratio.

Industry-typical guidance for a small injected two-stroke like this is a quality synthetic or semi-synthetic two-stroke oil rated for injector use — commonly carrying a JASO FB, FC, or FD rating, or an API TC classification. These oils are blended to burn cleanly, resist carbon formation, and keep the exhaust port and spark plug from fouling. Heavily castor-based premix oils, while excellent in some racing applications, tend to gum up injection pumps and are a poor match for an automatic oiling system. If you are unsure whether a bottle is injector-safe, the label will tell you; if it only lists premix ratios, treat it as premix-only.

Premix Ratios and Why the PW50 Is a Special Case

Because the PW50 meters its own oil, there is no ratio for you to calculate at the pump under normal operation. The injection pump delivers oil at a rate that works out to roughly the equivalent of a 50:1 mix under typical running conditions, leaning slightly richer under load and slightly leaner at light throttle. That automatic adjustment is one of the advantages of injection over premix, and it is why the PW50 is such a forgiving bike for young or new riders.

If the injection system has been removed or bypassed — something that happens on modified or race-prepped examples — you are back to premixing, and common two-stroke ratios fall in the 32:1 to 50:1 range depending on the oil and the state of tune. Running too little oil starves the top end; running far too much fouls plugs, loads the exhaust with carbon, and makes the bike run poorly. Confirm the ratio your specific setup calls for rather than guessing.

Transmission Oil for the Automatic Gearbox

The gearbox and wet clutch on the PW50 share a small oil sump, and because the clutch is bathed in that same oil, the fluid choice matters more than the volume suggests. Motorcycle-specific oil is the right call here. Automotive oils frequently contain friction modifiers that are fine for a car engine but cause a wet clutch to slip, grab, or wear prematurely. Look for a JASO MA or MA2 rating on the bottle.

Viscosity-wise, most small two-stroke gearboxes in this class commonly spec something in the 10W-30 or 10W-40 range, and either a conventional or synthetic motorcycle oil will work. The total capacity is small — measured in a few hundred milliliters rather than quarts — so it is worth measuring carefully rather than pouring freely. Overfilling can push oil past seals, and underfilling puts the clutch at risk.

Final Drive Gear Oil on the Shaft-Driven PW50

Because the PW50 sends power to the rear wheel through a shaft rather than a chain, there is a small gear case at the wheel end that holds its own lubricant. This is a separate fluid from the transmission oil and is serviced separately. Gear oil in the 80W-90 range is the typical family of lubricant used in small shaft drive units, though the exact recommendation for this bike is worth checking before you buy. The volume is very small, often well under 200 milliliters, so a single bottle lasts a long time.

Why the Correct Oil Matters on a Small Two-Stroke

Small displacement two-strokes are sensitive to oil quality in ways that bigger engines are not. A low-grade or wrong-type two-stroke oil leaves carbon deposits on the piston crown, ring grooves, and exhaust port. Over time that carbon sticks rings, reduces compression, and chokes the exhaust, and the bike loses the crisp throttle response it should have. Spark plug fouling is the more immediate symptom, showing up as hard starting or a bike that dies at idle.

On the gearbox side, the failure mode is different but just as real. Friction-modified automotive oil lets the centrifugal clutch slip under load, which shows up as sluggish acceleration and eventually as a burned clutch. Using the right motorcycle-specific oil protects the clutch and keeps the automatic transmission shifting the way it was designed to.

Confirming the Exact Specs for Your 2013 PW50

The guidance above reflects what is typical and widely accepted for this class of bike, and it will get you riding confidently. For the precise figures — the exact gearbox capacity, the final drive fluid recommendation, and Yamaha's preferred two-stroke oil specification — your owner's manual is the authoritative source, and a quick look takes only a minute. A Yamaha dealer can also confirm the numbers if the manual has gone missing. Treat that as a fast verification step, not a reason to delay getting the bike serviced.

Related Shopping Categories

Shop Oils and Fluids for a 2013 Yamaha PW50 Dirt Bike.

Shop Oil for a 2013 Yamaha PW50 Dirt Bike.

Shop Air Filters and Oil for a 2013 Yamaha PW50 Dirt Bike.

Shop Transmission for a 2013 Yamaha PW50 Dirt Bike.

Shop Oil Filters for a 2013 Yamaha PW50 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.