What Type of Oil Does a 1995 Yamaha RT100 Dirt Bike Take?

Shop parts for a 1995 Yamaha RT100 Dirt Bike.

The RT100 Runs Two Separate Oils, Not One

The 1995 Yamaha RT100 is a 100cc air-cooled two-stroke single, and that one design fact shapes everything about how it gets lubricated. A four-stroke engine circulates a single sump of oil through the crankcase, valvetrain, and clutch, so one fluid does all the work. A two-stroke splits that job in half. One oil handles combustion lubrication, and a completely separate oil handles the transmission. Treating those as the same fluid, or assuming one oil covers both, is the most common mistake new RT100 owners make.

Yamaha shipped the RT100 with an oil injection system, which meters two-stroke oil from a dedicated tank into the intake tract automatically as you ride. Most riders therefore never mix oil into their fuel at all — they simply keep the injection tank topped off with a quality two-stroke oil. Some owners, particularly those reviving a bike with a failed or removed injection pump, convert to premix instead. Both approaches work fine, but they call for different oils and different habits, so it is worth knowing which setup your bike is running before you buy anything.

Choosing a Two-Stroke Oil for the Injection Tank

For the injection system, you want a two-stroke oil formulated for oil injection rather than a premix-only racing oil. Modern two-stroke oils are almost universally synthetic or semi-synthetic, and they are engineered to burn cleanly, resist carbon buildup on the piston crown and exhaust port, and keep the small end of the connecting rod well lubricated at the RPMs a 100cc trail bike sees. A dedicated two-stroke oil is not the same product as a four-stroke motor oil, and it is not the same as a general-purpose lubricant. It has to be designed to combust.

Look for an oil labeled for injector use or dual-purpose injector/premix service. These are widely available in both mineral and full-synthetic formulations. Full synthetics generally hold up better under heat and leave less ash behind, which matters on a small air-cooled engine that runs hot on slow trails. Mineral two-stroke oils are cheaper and still perfectly serviceable for a lightly used RT100, though they tend to smoke a bit more and foul plugs sooner if the bike is lugged around at low RPM.

Premix Ratios If Your RT100 Has Been Converted

If the injection pump on your RT100 has been removed or disabled, you will be mixing oil into the fuel yourself. Common two-stroke premix ratios fall in the range of 32:1 to 50:1, with 32:1 and 40:1 being the most frequently cited for small-displacement trail engines of this era. A richer mix, meaning more oil per gallon, provides more lubrication but burns dirtier and can foul plugs. A leaner mix runs cleaner but offers less protection if the engine is worked hard.

Whichever ratio you settle on, measure it consistently with a proper ratio cup rather than eyeballing it. Inconsistent mixing is far more damaging than picking a slightly different ratio than the factory recommended. If you are unsure which ratio suits your bike, a 32:1 mix is the safer starting point for a small air-cooled two-stroke, and you can adjust from there based on how the plug reads and how the bike runs.

Transmission Oil for the RT100 Gearbox

The gearbox on the RT100 is a separate lubrication system entirely, and it has nothing to do with the fuel or the injection tank. Most two-stroke dirt bikes in this class use a conventional or synthetic motorcycle-specific gear oil in a viscosity range around 10W-30 or 10W-40. Because the transmission shares its oil with a wet clutch, the fluid needs to be formulated for that environment. Automotive engine oils often contain friction modifiers that let a wet clutch slip under load, which shows up as a mushy, slipping feel when you get on the throttle.

Look for a motorcycle-specific transmission or gear oil, ideally carrying a JASO MA or MA2 rating, which confirms it is compatible with wet clutch packs. Some riders run a dedicated gear oil, while others use a motorcycle-specific engine oil of the correct weight. Either can work, but the key is that the product is intended for a wet clutch and not a car engine.

Why the Right Oil Protects This Little Engine

Small air-cooled two-strokes are less forgiving than their larger, liquid-cooled cousins. Running the wrong two-stroke oil, or a premix ratio that is too lean, accelerates carbon buildup on the piston and exhaust port, shortens spark plug life, and can eventually score the cylinder. Running too rich a mix fouls plugs and gums up the power valve area, though the RT100 is a simple engine without a power valve, so the main penalty is smoke and plug fouling.

On the transmission side, using an automotive oil with friction modifiers will gradually wear the clutch plates and leave you with a slipping clutch that no amount of adjustment will fix. Using the correct wet-clutch-compatible fluid keeps shifting crisp and clutch engagement predictable for far longer.

Confirming the Exact Specs for Your Bike

The guidance above reflects what is typical for a 1995 RT100 and for small two-stroke trail bikes of that era, but the precise injection oil recommendation, premix ratio, and gearbox viscosity for your specific machine are best confirmed against your owner's manual or by asking a Yamaha dealer. That is a quick check, not a hurdle — a minute of verification tells you exactly what your bike wants, and then you can buy with confidence and get back to riding.

Related Shopping Categories

Shop Oils and Fluids for a 1995 Yamaha RT100 Dirt Bike.

Shop Oil for a 1995 Yamaha RT100 Dirt Bike.

Shop Air Filters and Oil for a 1995 Yamaha RT100 Dirt Bike.

Shop Transmission for a 1995 Yamaha RT100 Dirt Bike.

Shop Oil Filters for a 1995 Yamaha RT100 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.