What Type of Oil Does a 1987 Yamaha PW50 Dirt Bike Take?
Shop parts for a 1987 Yamaha PW50 Dirt Bike.
Two Separate Lubrication Jobs on One Little Two-Stroke
The 1987 Yamaha PW50 is a 49cc air-cooled two-stroke, and like most two-strokes it relies on two completely separate lubrication systems that call for two completely different oils. The first is the oil that ends up in the combustion chamber, either mixed with gasoline or metered in by an injection pump. The second is the gearbox oil that bathes the transmission and clutch inside the engine cases. Treating those as one fluid, or assuming a single jug covers both jobs, is the most common mistake new PW50 owners make. Each system has its own fill point, its own service interval, and its own oil specification, and getting them straight is the whole game.
Combustion-Side Oil: Injection on the PW50, Premix as an Alternative
Yamaha equipped the PW50 with its Autolube oil injection system, which means the bike carries two-stroke oil in a dedicated tank and a pump meters it into the intake tract as the engine runs. That setup is convenient: you fill the oil tank with two-stroke oil, fill the gas tank with straight gasoline, and ride. Whatever you pour into that injection tank needs to be a dedicated two-stroke oil — not motor oil, not gear oil, not an automotive product of any kind. Modern two-stroke oils are almost universally synthetic or semi-synthetic blends formulated to burn cleanly, resist carbon buildup on the piston crown and exhaust port, and stay thin enough to flow through a small pump and a narrow oil line. A quality JASO FD or ISO-L-EGD rated two-stroke oil is the industry-typical pick for a small air-cooled engine like this one.
Some owners delete the injection system and run premix instead, usually because the pump has failed or because they want to simplify the bike. If your PW50 has been converted to premix, you mix two-stroke oil directly into the gasoline can before fueling rather than relying on the pump.
Premix Ratios for a Small Air-Cooled Two-Stroke
If you are mixing at the pump, the ratio matters as much as the oil. Common two-stroke premix ratios fall in the 32:1 to 50:1 range, and which end of that range is right depends on the oil you're using and how the engine is set up. A 32:1 mix, roughly four ounces of oil per gallon of gas, sits on the rich side and is a safe, widely used ratio for small air-cooled engines that spend a lot of time at wide-open throttle. A 50:1 mix, about 2.6 ounces per gallon, is leaner and is typical of modern full-synthetic oils engineered to protect adequately at lower concentrations.
Running too little oil starves the piston, ring, and cylinder of lubrication and accelerates wear in a hurry. Running far too much oil fouls spark plugs, gums up the exhaust, and lays down heavy carbon deposits. If you're unsure which ratio your bike was set up for, 32:1 with a quality two-stroke oil is a conservative, commonly used starting point — but confirm the figure that applies to your specific machine before you commit to it.
Gearbox Oil: A Separate Fluid With Its Own Spec
The PW50's transmission, centrifugal clutch, and shaft final drive live in a separate oil bath inside the engine cases, and that oil never touches the combustion chamber. This is the fluid you drain and refill during a gearbox oil change, and it is a completely different product from the two-stroke oil in the injection tank. Most small two-stroke dirt bikes in this class commonly spec a motorcycle-specific gear oil or engine oil in the 10W-30 or 10W-40 range, and the PW50 generally falls in that same neighborhood.
Because the clutch is a wet centrifugal unit bathed in this oil, you want a lubricant that is friendly to wet clutches. A motorcycle-specific oil without friction modifiers is the safe choice; automotive oils marketed as "energy conserving" can cause clutch slip and inconsistent engagement. Capacity is small on a bike this size, so measure carefully rather than pouring until it looks full, and check the level the way your manual describes.
Why the Correct Oil and Ratio Matter
Two-stroke engines are unforgiving about lubrication because the oil is consumed as part of the combustion process. Use the wrong type and you get carbon buildup on the piston crown, ring sticking, and a plugged exhaust port that quietly robs power. Get the ratio wrong on the lean side and you risk a seized piston; get it wrong on the rich side and you'll be swapping fouled plugs and cleaning goo out of the exhaust. On the gearbox side, the consequences are slower but just as real: the wrong oil or a contaminated fill wears the clutch and transmission internals, and friction-modified automotive oil can make the clutch grab and slip unpredictably. Both systems are cheap to service correctly and expensive to repair after neglect.
Confirming the Exact Specification for Your Bike
The guidance above reflects what is typical for a small air-cooled two-stroke of this era, and it will get you riding with confidence. For full precision on your particular machine, the owner's manual is the fastest source for the exact injection oil recommendation, the premix ratio if applicable, and the gearbox oil viscosity and capacity. A Yamaha dealer can confirm the same details in a minute or two if the manual has gone missing over the decades. Treat that as a quick confirmation step, not a roadblock — then get the bike fueled, oiled, and out on the track.
Related Shopping Categories
Shop Oils and Fluids for a 1987 Yamaha PW50 Dirt Bike.
Shop Oil for a 1987 Yamaha PW50 Dirt Bike.
Shop Air Filters and Oil for a 1987 Yamaha PW50 Dirt Bike.
Shop Transmission for a 1987 Yamaha PW50 Dirt Bike.
Shop Oil Filters for a 1987 Yamaha PW50 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.