What Type of Oil Does a 1978 Yamaha IT250 Dirt Bike Take?

Shop parts for a 1978 Yamaha IT250 Dirt Bike.

The 1978 Yamaha IT250 is a two-stroke enduro machine, and that single fact shapes every answer to the oil question. There is no crankcase full of engine oil to top off, no oil filter to swap, and no single fluid that covers the whole bike. Instead, a two-stroke like the IT250 splits its lubrication needs into two completely separate systems: the oil that gets burned along with the fuel, and the oil that lives inside the transmission. Getting both right is what keeps a forty-plus-year-old enduro bike running clean and shifting smoothly.

Two Separate Lubrication Systems, Two Separate Answers

On a two-stroke engine, the crankshaft, connecting rod, and piston are lubricated by oil that arrives with the fuel charge. That oil burns off during combustion, which is why a two-stroke always consumes oil and always leaves a little smoke behind. Nothing recirculates, so nothing needs draining at the end of a ride.

The transmission, by contrast, sits in its own sealed cavity and holds a fixed sump of gear oil that stays in the bike for many hours of riding. It never mixes with the fuel and never burns. That means the IT250 owner is really shopping for two different products, and confusing one for the other is the most common mistake riders make on older two-strokes.

Some two-strokes of this era used an oil injection pump that metered oil automatically from a separate tank. Others, including many of the IT enduro models, relied on the rider to pre-mix oil into the fuel can. If your IT250 has an oil tank and a pump, it uses injection-spec oil. If it does not, you are mixing at the pump. A quick look at the bike settles the question in seconds.

Choosing a Two-Stroke Premix Oil

Modern two-stroke oils are almost all synthetic or semi-synthetic blends, and they are a genuine improvement over the straight mineral oils that were common when this bike was new. Synthetics resist breakdown at high combustion temperatures, burn more completely, and leave far less carbon behind on the piston crown, exhaust port, and power valve area.

Look for an oil explicitly labeled for air-cooled or liquid-cooled two-stroke motorcycle use, and preferably one carrying a JASO FD or ISO-L-EGD rating. Those ratings indicate a low-ash, low-deposit formulation, which matters on an engine that has no oil filter to catch anything. Avoid oils sold for outboard motors or chainsaws — they are formulated for different combustion temperatures and different duty cycles, and they do not protect a dirt bike engine the same way.

If your IT250 is oil-injected rather than premix, use an oil specifically rated for injection systems. Injector oils are blended thinner so they flow through the pump and lines reliably, and a thick premix-only oil can starve the pump in cold weather.

Premix Ratios for a Late-Seventies Enduro Two-Stroke

Premix ratios for two-stroke dirt bikes generally fall somewhere between 20:1 and 50:1, with the correct number depending on the engine, the oil, and how hard the bike is ridden. For a 1978 IT250, the commonly cited figure in period literature and in the vintage community is in the neighborhood of 32:1, though some older documentation calls for richer mixtures closer to 20:1 when using conventional mineral oil.

The logic behind the range is straightforward. Richer mixtures, meaning more oil per gallon, provide more lubrication but burn dirtier and can foul plugs. Leaner mixtures burn cleaner and make more power, but offer less protection if the engine is worked hard or jetted slightly lean. Modern synthetic oils tolerate leaner ratios than the mineral oils of the seventies, which is why a bike that once wanted 20:1 may run perfectly well at 32:1 or even 40:1 on a quality synthetic.

Whatever ratio you settle on, mix it consistently and measure it accurately. Guessing at the ratio from ride to ride is how engines get damaged. A ratio cup makes the job quick and repeatable.

Transmission and Gearbox Oil

The gearbox on the IT250 is a wet-clutch, constant-mesh transmission that shares its oil with the clutch pack. That means the fluid has to do two jobs at once: lubricate gears and bearings, and allow the clutch plates to grip and release predictably.

Most two-stroke dirt bikes in this class run a motorcycle-specific gear oil in the 10W-30 or 10W-40 range, and that is a sensible starting point for the IT250. The key requirement is that the oil be formulated for wet clutches, typically indicated by a JASO MA or MA2 rating. Standard automotive engine oils often contain friction modifiers designed to reduce drag, and those same additives can cause a wet clutch to slip under load. That is a real problem on a bike that has to hook up out of a muddy corner.

Either conventional or synthetic gear oil will work. Synthetics hold up better under sustained heat and tend to shift more consistently as they age, while conventional oil costs less and is perfectly adequate for a bike that sees regular changes. Because the transmission oil is a closed sump, it is serviced on its own schedule, completely independent of what you pour into the fuel can.

Why the Correct Oil and Ratio Actually Matter

Running the wrong premix oil or a badly chosen ratio shows up in predictable ways. Too much oil, or an oil that does not burn cleanly, leads to heavy carbon deposits on the piston crown and exhaust port, a fouled spark plug, and a bike that smokes excessively and runs rough at low throttle. Too little oil, or an oil that breaks down under heat, accelerates ring and cylinder wear and can eventually seize the piston.

On the transmission side, the wrong fluid tends to announce itself through clutch behavior. Slipping under acceleration, a grabby engagement from a stop, or a notchy shift feel are all signs that the gear oil is not suited to a wet clutch. Using a proper motorcycle-specific oil in the correct viscosity range avoids most of these complaints entirely.

Confirming the Exact Specification for Your IT250

The guidance above reflects what is typical and widely accepted for a late-seventies Yamaha two-stroke enduro bike, and it will get you riding confidently. For the precise factory figure, though, the owner's manual for your specific machine is the final word, and a Yamaha dealer can confirm the recommended premix ratio and gearbox oil viscosity if the manual is long gone.

It is worth the two minutes. Forty years of previous owners, swapped carburetors, and aftermarket exhausts mean no two surviving IT250s are set up identically, and a quick confirmation against the original spec removes any doubt before you mix your first tank.

Related Shopping Categories

Shop Oils and Fluids for a 1978 Yamaha IT250 Dirt Bike.

Shop Oil for a 1978 Yamaha IT250 Dirt Bike.

Shop Air Filters and Oil for a 1978 Yamaha IT250 Dirt Bike.

Shop Transmission for a 1978 Yamaha IT250 Dirt Bike.

Shop Oil Filters for a 1978 Yamaha IT250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.