Oil Choices for a 1977 Yamaha IT250: Premix, Gearbox, and What Actually Matters

Shop parts for a 1977 Yamaha IT250 Dirt Bike.

Two Separate Lubrication Jobs on the IT250

The 1977 Yamaha IT250 is a two-stroke enduro machine, and that single fact drives every oil decision you will make for it. A two-stroke engine does not carry a sump full of engine oil the way a four-stroke does. Lubrication for the crank bearings, piston skirt, and cylinder walls arrives either pre-mixed into the fuel or delivered by a pump. Meanwhile, the transmission gears and the clutch pack sit in their own sealed case and require a completely separate lubricant. Those are two different fluids doing two different jobs, and confusing them is the single most common mistake riders make when they first take on an older two-stroke.

So the honest answer to “what oil does it take” is really two answers: a two-stroke oil for combustion-side lubrication, and a gear oil for the transmission. Get both right and the bike will run clean and shift well for a long time.

Premix Oil: What to Look For

Two-stroke oil is formulated to burn along with the fuel rather than to sit in a sump and be drained out later. That means it has to lubricate effectively at high temperature and then combust as completely as possible, leaving minimal ash and carbon behind. Modern two-stroke oils are overwhelmingly synthetic or semi-synthetic for exactly this reason — they resist carbon buildup on the piston crown, exhaust port, and power valve far better than the old low-detergent oils that were common when this bike was new.

Look for an oil explicitly labeled for two-stroke, air-cooled or liquid-cooled motorcycle use, and preferably one carrying a JASO FD or ISO-L-EGD rating. Those designations indicate a low-ash, low-smoke formulation designed for high-performance two-strokes. Avoid anything marketed as an outboard or chainsaw oil if you can; those are built for different operating conditions and often burn dirtier in a dirt bike engine.

Premix Ratios in Practice

If your IT250 runs on premix, the ratio matters as much as the oil itself. Across two-stroke dirt bikes generally, common ratios fall between 32:1 and 50:1, with 40:1 being a very widely used middle ground. Richer mixtures (more oil, such as 32:1) provide more lubrication but can foul plugs and gum up the exhaust if the jetting is not matched. Leaner mixtures (50:1) burn cleaner but leave less margin if the engine is worked hard or jetted slightly lean.

It is worth knowing that many Yamaha enduro models of this era, including several in the IT line, were factory-equipped with an oil injection system that metered two-stroke oil from a separate tank rather than requiring premix. Plenty of those systems have been removed over the decades by owners who preferred to mix their own fuel. Before you fill a tank, determine which setup your particular bike has — a small oil tank and pump, or a straight premix diet. If the injection system is intact and working, you fill that tank with the same quality two-stroke oil and leave the fuel straight.

Gearbox and Clutch Oil

The transmission side of the IT250 is a wet-clutch, constant-mesh gearbox, and it needs its own oil. Most two-stroke dirt bikes in this displacement class commonly spec a motorcycle-specific gear oil in the 10W-30 or 10W-40 range, and that is a reasonable starting point for the IT250 as well. What matters more than the exact number is that the oil is designed for a wet clutch. Automotive oils frequently contain friction modifiers that let the clutch slip under load, which shows up as a mushy engagement and eventually as a burned clutch pack.

Look for a JASO MA or MA2 rated product, or a dedicated transmission fluid sold for two-stroke motocross and enduro bikes. Synthetic gear oils hold up better under the heat and shear that a clutch generates, while conventional oils are cheaper and perfectly serviceable for a rider who changes them on a reasonable schedule. Either way, this is a completely separate service from anything you do to the fuel.

Why the Wrong Oil or Ratio Costs You

Running a poor-quality two-stroke oil or a badly chosen ratio tends to show up in predictable ways. Carbon deposits build on the piston crown and ring lands, the exhaust port gradually closes up with gunk, and spark plugs foul repeatedly. In severe cases, inadequate lubrication scores the cylinder or seizes the piston. On the gearbox side, the wrong fluid shows up as notchy shifting, clutch drag, or a clutch that slips when you get on the throttle hard out of a corner.

None of these failures happen overnight, which is exactly why they are easy to ignore until they are expensive. Using a quality two-stroke oil at a sensible ratio and a wet-clutch-compatible gear oil is cheap insurance on a bike this old.

Confirming the Exact Spec for Your Specific Bike

Everything above reflects what is typical and widely accepted for two-stroke enduros of this class and era, and it will get you riding confidently. For the precise figures — the exact premix ratio Yamaha specified, the recommended gearbox viscosity, and the correct fill quantity — a quick look at the owner's manual or a call to a Yamaha dealer familiar with vintage models settles it in a minute or two. That is a confirmation step, not a reason to hold off. Pick a reputable two-stroke oil, pick a wet-clutch-safe gear oil, verify the numbers, and get the IT250 back on the trail where it belongs.

Related Shopping Categories

Shop Oils and Fluids for a 1977 Yamaha IT250 Dirt Bike.

Shop Oil for a 1977 Yamaha IT250 Dirt Bike.

Shop Air Filters and Oil for a 1977 Yamaha IT250 Dirt Bike.

Shop Transmission for a 1977 Yamaha IT250 Dirt Bike.

Shop Oil Filters for a 1977 Yamaha IT250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.