Replacing the Fuel Line on a 2020 Sherco 300SE-R
Shop parts for a 2020 Sherco 300SE-R Dirt Bike.
If you have owned your 2020 Sherco 300SE-R more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.
Confirming the Fuel System on Your 2020 Sherco 300SE-R
The fuel system on your 2020 Sherco 300SE-R uses a carburetor, and the petcock is your shutoff. Fuel flows by gravity alone from tank to float bowl through one hose, secured at each end by a spring pinch clamp or a small screw clamp. That is the whole circuit, and it is why this job is beginner-friendly on a two-stroke machine.
What a Dying Fuel Line Looks Like
Most failing fuel lines warn you before letting go. The warnings are easy to dismiss, so it helps to know what you are looking at when you walk up to your 2020 Sherco 300SE-R.
- A puddle or damp patch underneath. Even a slow weep leaves evidence, usually below the tank or carburetor.
- A strong fuel smell in the garage. Odor lingering a day after parking is not normal.
- Visible cracking. Bend the hose gently; fine cracks that open under flex mean the rubber is done.
- A hose that feels hard or glazed. Healthy line is soft and slightly tacky.
- Bogging or running lean. A collapsed or deteriorated line restricts flow, and the engine acts like the tank is nearly empty.
Why Fuel Lines Harden, Crack, and Fail
Rubber fuel line fails for reasons that have little to do with how hard you ride. Age drives it: the plasticizers keeping the hose flexible slowly migrate out, and pliable rubber turns stiff and glassy, so a small flex — bolting the tank down, rocking the bike onto a stand — opens a hairline crack. Dry, hot storage accelerates that, pulling volatiles out faster than a temperate garage would. Ethanol-blended pump fuel left sitting in the hose adds a second mechanism, attacking the inner wall and leaving gum that can flake into the fuel path on a 2020 Sherco 300SE-R.
What to Have on the Bench
The parts list is short and the tool list shorter. Lay it out before breaking the first connection.
- Replacement fuel line in the correct inside diameter and length for your 2020 Sherco 300SE-R. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.
Draining Down and Pulling the Line
Shut the petcock off first. That single step keeps this job clean on a carbureted 300SE-R — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.
Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.
With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.
Fitting the New Line
Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.
Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your 300SE-R is about to run.
Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.
Leak Check Before You Ride
Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.
Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.
Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our full guide to dirt bike fuel line care.
Related Shopping Categories
Shop Fuel Lines for a 2020 Sherco 300SE-R Dirt Bike.
Shop Fuel Line Clamps for a 2020 Sherco 300SE-R Dirt Bike.
Shop Petcocks for a 2020 Sherco 300SE-R Dirt Bike.
Shop Fuel Filters for a 2020 Sherco 300SE-R Dirt Bike.
Shop Fuel Stabilizer for a 2020 Sherco 300SE-R Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.