Getting a Fresh Fuel Line Onto Your 2018 Sherco 125SE-R

Shop parts for a 2018 Sherco 125SE-R Dirt Bike.

Fuel line replacement sits near the top of the high-value, low-difficulty maintenance list on a 2018 Sherco 125SE-R. The hose is short, the fittings are simple, and the payoff is a fuel system you can stop worrying about. What follows covers identifying what you have, spotting a line on its way out, and getting the new one leak-free.

Symptoms Worth Catching Early

Catching a bad line early is mostly about paying attention during routine checks. On a 2018 Sherco 125SE-R, these signals should send you looking at the hose.

  • Wet spots on the frame or cases. Fuel evaporates fast, so look for residue rather than liquid.
  • Fuel odor that will not clear. A leak too small to see is still large enough to smell.
  • Hairline splits near the clamps. The clamped section takes the most stress and cracks first.
  • Hose that holds its bend. If the line refuses to straighten, the rubber has hardened.
  • Symptoms resembling a fueling fault. Bogging on hills or running lean with a full tank.

The Carbureted Setup on This 125SE-R

Before anything comes apart, confirm what you have. The 2018 Sherco 125SE-R is carbureted, identifiable by the petcock threaded into the bottom of the tank and a plain rubber hose running to the carburetor inlet. No fuel pump sits in the circuit and no pressure needs relieving, which removes the most awkward part of this repair.

Why Fuel Lines Harden, Crack, and Fail

Rubber fuel line fails for reasons that have little to do with how hard you ride. Age drives it: the plasticizers keeping the hose flexible slowly migrate out, and pliable rubber turns stiff and glassy, so a small flex — bolting the tank down, rocking the bike onto a stand — opens a hairline crack. Dry, hot storage accelerates that, pulling volatiles out faster than a temperate garage would. Ethanol-blended pump fuel left sitting in the hose adds a second mechanism, attacking the inner wall and leaving gum that can flake into the fuel path on a 2018 Sherco 125SE-R.

What to Have on the Bench

Assemble everything first. Once the line is off, you do not want to be driving to the parts store with an open fuel system.

  • Replacement fuel line in the correct inside diameter and length for your 2018 Sherco 125SE-R. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.

Getting the Old Line Out of the Way

Close the petcock. Everything downstream of that valve is the only fuel you need to deal with, which on a 2018 Sherco 125SE-R amounts to a few ounces in the line and float bowl.

Get that remaining fuel into a container rather than onto the floor. The float bowl drain screw is purpose-built for this — slip a hose over the nipple, aim it into your catch can, and crack the screw open. If you would rather drain the whole tank, do it now with the hose routed into the container.

Then release both clamps and work the hose off the fittings. Pliers handle spring clamps; a flat screwdriver handles screw clamps. Slide each clamp well back so it cannot fight you. To separate a stubborn hose from a barb, rotate it a quarter turn to shear the bond before pulling. If the rubber has gone hard enough that it will not release, split it with a knife along its length — the hose is being replaced anyway, and the fittings are what matter.

Installing the Replacement Hose

Measure the replacement against the old line before cutting. Matching the original length keeps routing correct on the 125SE-R, and a square cut gives the clamp a clean surface to seal against. Trim with a fresh blade rather than dull side cutters.

Slide the hose fully onto the tank-side fitting, past the barb and up against the shoulder. If the rubber resists, soften it in hot water; do not reach for lubricant. Grease or oil on a fuel fitting shows up later as a slow weep and can carry contamination into the carburetor.

Attach the carburetor end and check the shape of the run. The hose should follow the original path with no contact against cylinder or exhaust and no kink where it curves. Install fresh clamps over the fitting area rather than out on bare hose, and tighten only until the rubber is compressed — a screw clamp cranked down hard will eventually cut through.

Verifying the Repair

Open the fuel valve and let gravity do the testing. Give the 125SE-R a few minutes standing over clean cardboard, then inspect the tank-side and carburetor-side joints carefully. Wipe each dry first so new moisture is unmistakable.

Follow that with a running check. Start the engine, bring it to temperature, and look at both fittings again at idle — some leaks only appear once heat and vibration are in the system. A joint weeping under those conditions has a seating problem, not a clamp problem; pull it apart and push the hose fully home.

Then clean up and stay attentive for a ride or two. Dispose of old fuel properly, watch the clamps as the new rubber settles, and consider replacing an inline filter while the system is open. Anyone wanting more detail on what shortens fuel line life long term will find it in our full guide to dirt bike fuel line care.

Related Shopping Categories

Shop Fuel Lines for a 2018 Sherco 125SE-R Dirt Bike.

Shop Fuel Line Clamps for a 2018 Sherco 125SE-R Dirt Bike.

Shop Petcocks for a 2018 Sherco 125SE-R Dirt Bike.

Shop Fuel Filters for a 2018 Sherco 125SE-R Dirt Bike.

Shop Fuel Stabilizer for a 2018 Sherco 125SE-R Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.