Replacing the Fuel Line on a 2017 KTM 50SX

Shop parts for a 2017 KTM 50SX Dirt Bike.

A cracked fuel line seems trivial until it strands you at the far end of a trail or drips onto a hot pipe. On a 2017 KTM 50SX, the fuel line is a short, inexpensive piece of rubber doing a job with zero tolerance for failure — and replacing it is well within reach with basic hand tools and about half an hour.

The Carbureted Setup on This 50SX

Fuel delivery on the 2017 KTM 50SX is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.

How a Failing Line Announces Itself

Most failing fuel lines warn you before letting go. The warnings are easy to dismiss, so it helps to know what you are looking at when you walk up to your 2017 KTM 50SX.

  • A puddle or damp patch underneath. Even a slow weep leaves evidence, usually below the tank or carburetor.
  • A strong fuel smell in the garage. Odor lingering a day after parking is not normal.
  • Visible cracking. Bend the hose gently; fine cracks that open under flex mean the rubber is done.
  • A hose that feels hard or glazed. Healthy line is soft and slightly tacky.
  • Bogging or running lean. A collapsed or deteriorated line restricts flow, and the engine acts like the tank is nearly empty.

Getting Set Up Before You Start

Assemble everything first. Once the line is off, you do not want to be driving to the parts store with an open fuel system.

  • Replacement fuel line in the correct inside diameter and length for your 2017 KTM 50SX. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.

What Actually Kills a Fuel Line

The failure is chemical and thermal more than mechanical. Fuel hose stays soft because of additives in the rubber, and those additives leave over time — faster in heat, faster still in the dry air of an arid climate. A hose in that state has lost its ability to seal around a barb, so it seeps before it visibly splits. Fuel left standing does its own damage: ethanol blends draw in moisture and degrade after months of sitting, and the byproducts attack rubber and leave sticky residue. If your 2017 KTM 50SX winters with fuel in the system, the line ages on the calendar rather than the odometer.

Removing the Old Fuel Line

Close the petcock. Everything downstream of that valve is the only fuel you need to deal with, which on a 2017 KTM 50SX amounts to a few ounces in the line and float bowl.

Get that remaining fuel into a container rather than onto the floor. The float bowl drain screw is purpose-built for this — slip a hose over the nipple, aim it into your catch can, and crack the screw open. If you would rather drain the whole tank, do it now with the hose routed into the container.

Then release both clamps and work the hose off the fittings. Pliers handle spring clamps; a flat screwdriver handles screw clamps. Slide each clamp well back so it cannot fight you. To separate a stubborn hose from a barb, rotate it a quarter turn to shear the bond before pulling. If the rubber has gone hard enough that it will not release, split it with a knife along its length — the hose is being replaced anyway, and the fittings are what matter.

Routing and Securing the New Line

Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.

Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your 50SX is about to run.

Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.

Confirming It Is Sealed

With the new line in place, open the petcock and stop. Let the 2017 KTM 50SX sit five minutes over a clean surface and use that time to examine both joints under a flashlight. A properly seated hose stays completely dry; anything else needs attention before the wheels turn.

The running test comes second. Fire the engine, let it warm, and look again — expansion and vibration find seals that hold fine cold and still. When you find a weep, resist the urge to overtighten. Disconnect, verify the hose is pushed fully over the barb, and reassemble; that is nearly always the actual problem.

Wrap up by disposing of the drained fuel appropriately and taking another look at the connections after your next ride. On carbureted bikes an inline filter, if fitted, is a serviceable part worth replacing at the same time. For deeper background on keeping fuel lines healthy between seasons, our complete overview of dirt bike fuel line service is a useful companion read.

Related Shopping Categories

Shop Fuel Lines for a 2017 KTM 50SX Dirt Bike.

Shop Fuel Line Clamps for a 2017 KTM 50SX Dirt Bike.

Shop Petcocks for a 2017 KTM 50SX Dirt Bike.

Shop Fuel Filters for a 2017 KTM 50SX Dirt Bike.

Shop Fuel Stabilizer for a 2017 KTM 50SX Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.