Replacing the Fuel Line on a 2017 Beta 300 RR

Shop parts for a 2017 Beta 300 RR Dirt Bike.

Rubber fuel hose is among the cheapest parts on a 2017 Beta 300 RR and one of the few that can end a ride outright. It hardens, cracks, and weeps fuel where you cannot see it, eventually either starving the engine or putting gasoline somewhere it should never be. Swapping it needs no specialty tools and no shop time.

Start by Tracing the Fuel Path

Before anything comes apart, confirm what you have. The 2017 Beta 300 RR is carbureted, identifiable by the petcock threaded into the bottom of the tank and a plain rubber hose running to the carburetor inlet. No fuel pump sits in the circuit and no pressure needs relieving, which removes the most awkward part of this repair.

Why Fuel Lines Harden, Crack, and Fail

Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 2017 Beta 300 RR has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.

Symptoms Worth Catching Early

Fuel line problems show up two ways: something you see and smell, or something you feel while riding. Both are worth taking seriously on a 300 RR.

  • Evidence on the ground. A drip or dark patch under the bike after it sits overnight.
  • The smell of raw gasoline. Noticeable with the engine cold and unrun.
  • Surface cracking on the hose. Especially at bends and where the line slides over fittings.
  • Weeping under light pressure. Push gently near a fitting and watch for moisture at the joint.
  • Fuel starvation symptoms. Bogging or cutting out as though the tank ran dry when it clearly has not.

What to Have on the Bench

Assemble everything first. Once the line is off, you do not want to be driving to the parts store with an open fuel system.

  • Replacement fuel line in the correct inside diameter and length for your 2017 Beta 300 RR. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.

Taking the Failed Hose Off

Shut the petcock off first. That single step keeps this job clean on a carbureted 300 RR — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.

Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.

With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.

Getting the New Line Seated Properly

Measure the replacement against the old line before cutting. Matching the original length keeps routing correct on the 300 RR, and a square cut gives the clamp a clean surface to seal against. Trim with a fresh blade rather than dull side cutters.

Slide the hose fully onto the tank-side fitting, past the barb and up against the shoulder. If the rubber resists, soften it in hot water; do not reach for lubricant. Grease or oil on a fuel fitting shows up later as a slow weep and can carry contamination into the carburetor.

Attach the carburetor end and check the shape of the run. The hose should follow the original path with no contact against cylinder or exhaust and no kink where it curves. Install fresh clamps over the fitting area rather than out on bare hose, and tighten only until the rubber is compressed — a screw clamp cranked down hard will eventually cut through.

Final Checks and the First Start

Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.

Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.

Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our evergreen guide to fuel line care and replacement.

Related Shopping Categories

Shop Fuel Lines for a 2017 Beta 300 RR Dirt Bike.

Shop Fuel Line Clamps for a 2017 Beta 300 RR Dirt Bike.

Shop Petcocks for a 2017 Beta 300 RR Dirt Bike.

Shop Fuel Filters for a 2017 Beta 300 RR Dirt Bike.

Shop Fuel Stabilizer for a 2017 Beta 300 RR Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.