Getting a Fresh Fuel Line Onto Your 2016 Yamaha PW50
Shop parts for a 2016 Yamaha PW50 Dirt Bike.
Rubber fuel hose is among the cheapest parts on a 2016 Yamaha PW50 and one of the few that can end a ride outright. It hardens, cracks, and weeps fuel where you cannot see it, eventually either starving the engine or putting gasoline somewhere it should never be. Swapping it needs no specialty tools and no shop time.
The Carbureted Setup on This PW50
Fuel delivery on the 2016 Yamaha PW50 is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.
Warning Signs Your PW50 Needs a New Line
Most failing fuel lines warn you before letting go. The warnings are easy to dismiss, so it helps to know what you are looking at when you walk up to your 2016 Yamaha PW50.
- A puddle or damp patch underneath. Even a slow weep leaves evidence, usually below the tank or carburetor.
- A strong fuel smell in the garage. Odor lingering a day after parking is not normal.
- Visible cracking. Bend the hose gently; fine cracks that open under flex mean the rubber is done.
- A hose that feels hard or glazed. Healthy line is soft and slightly tacky.
- Bogging or running lean. A collapsed or deteriorated line restricts flow, and the engine acts like the tank is nearly empty.
What to Have on the Bench
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 2016 Yamaha PW50. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.
Why Rubber Fuel Hose Gives Up
It helps to treat fuel line as a consumable rather than a permanent part. The material is engineered to stay soft and seal against a barbed fitting, and it loses that ability gradually as heat cycling, sun exposure, and plain calendar age push it the same direction — a dry climate does it fastest. Fuel chemistry compounds the problem. Ethanol blends sitting through a long off-season absorb water and begin to separate, which is harder on rubber than fresh fuel and leaves gum behind. On a 2016 Yamaha PW50 stored more than ridden, that combination is the usual culprit.
Removing the Old Fuel Line
Shut the petcock off first. That single step keeps this job clean on a carbureted PW50 — with the valve closed, the tank stays full and the only fuel to manage is what is already past the valve.
Empty the carburetor next. Attach a length of clear hose to the float bowl drain nipple, direct it into your container, and open the drain screw. A minute later the bowl is dry and you can work without fuel running down your arm.
With the fuel handled, address the clamps at each end. Squeeze spring clamp tabs together with pliers and walk the clamp down the hose, or loosen a screw clamp with a driver. The hose is usually the hard part: years of heat cycling effectively glue it to the barb. Twist first to break the bond, then pull straight off. When a line is badly hardened, cutting it off with a razor blade is safer for the fitting than prying at it.
Getting the New Line Seated Properly
Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.
Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your PW50 is about to run.
Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.
Leak Check Before You Ride
Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.
Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.
Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our complete overview of dirt bike fuel line service.
Related Shopping Categories
Shop Fuel Lines for a 2016 Yamaha PW50 Dirt Bike.
Shop Fuel Line Clamps for a 2016 Yamaha PW50 Dirt Bike.
Shop Petcocks for a 2016 Yamaha PW50 Dirt Bike.
Shop Fuel Filters for a 2016 Yamaha PW50 Dirt Bike.
Shop Fuel Stabilizer for a 2016 Yamaha PW50 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.