A Practical Fuel Line Walkthrough for the 2013 Yamaha TW200
Shop parts for a 2013 Yamaha TW200 Dirt Bike.
A cracked fuel line seems trivial until it strands you at the far end of a trail or drips onto a hot pipe. On a 2013 Yamaha TW200, the fuel line is a short, inexpensive piece of rubber doing a job with zero tolerance for failure — and replacing it is well within reach with basic hand tools and about half an hour.
Symptoms Worth Catching Early
Catching a bad line early is mostly about paying attention during routine checks. On a 2013 Yamaha TW200, these signals should send you looking at the hose.
- Wet spots on the frame or cases. Fuel evaporates fast, so look for residue rather than liquid.
- Fuel odor that will not clear. A leak too small to see is still large enough to smell.
- Hairline splits near the clamps. The clamped section takes the most stress and cracks first.
- Hose that holds its bend. If the line refuses to straighten, the rubber has hardened.
- Symptoms resembling a fueling fault. Bogging on hills or running lean with a full tank.
Understanding How the Line Deteriorates
Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 2013 Yamaha TW200 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.
Confirming the Fuel System on Your 2013 Yamaha TW200
The 2013 Yamaha TW200 runs a carbureted fuel system, which works in your favor. Fuel leaves the tank through a petcock — the small valve underneath — travels down a short rubber hose, and enters the carburetor at the float bowl inlet. You can shut fuel off at the source, and the line is a simple two-clamp affair with no pump pressure behind it.
What to Have on the Bench
Nothing here is exotic, but having it within reach before you open the fuel system keeps the job from turning messy.
- Replacement fuel line in the correct inside diameter and length for your 2013 Yamaha TW200. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.
Taking the Failed Hose Off
Petcock off, first thing. That valve is why a carbureted bike like the TW200 is forgiving here: shut it and the fuel stops moving.
Capture the fuel sitting downstream. Fit a clear hose to the float bowl drain nipple, run it to your container, and open the drain screw a couple of turns. The bowl empties in under a minute. Close the screw afterward, because a bowl that will not hold fuel is frustrating to diagnose later.
Clamps come next. Squeeze the ears of a spring clamp with pliers and slide it clear, or back off a screw clamp until it moves freely. Then persuade the hose off the barb with a twisting motion rather than a hard yank — old rubber bonds to metal, and a straight pull can bend a carburetor inlet or petcock spigot. When the line is truly seized, slice it lengthwise and peel it away.
Routing and Securing the New Line
Use the removed hose as your measuring stick and cut the new one to match. On a 2013 Yamaha TW200 the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.
Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.
Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.
Final Checks and the First Start
Restore fuel flow and watch. Open the petcock on your 2013 Yamaha TW200 and leave the bike sitting several minutes with clean cardboard underneath. Gravity finds a poor seal quickly. Look at both fittings with good light, and run a dry fingertip around each joint — fuel is easier to feel than to see.
Then start the engine and check again warm. Vibration and heat expose leaks a static test misses. If you see weeping at a clamp, do not simply crank it tighter; pull the joint apart and confirm the hose was fully seated on the barb, because an unseated hose will not seal at any clamp torque.
Finally, tidy up. Dispose of drained fuel properly rather than returning it to the tank if it looks cloudy or smells stale, and check the new hose after your first ride or two — new rubber takes a small set as it conforms to the fitting. For more background on how fuel quality and storage habits shorten hose life, our evergreen guide to fuel line care and replacement covers that ground in detail.
Related Shopping Categories
Shop Fuel Lines for a 2013 Yamaha TW200 Dirt Bike.
Shop Fuel Line Clamps for a 2013 Yamaha TW200 Dirt Bike.
Shop Petcocks for a 2013 Yamaha TW200 Dirt Bike.
Shop Fuel Filters for a 2013 Yamaha TW200 Dirt Bike.
Shop Fuel Stabilizer for a 2013 Yamaha TW200 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.