How the Fuel Line Comes Off and Goes Back On — 2013 Yamaha PW50

Shop parts for a 2013 Yamaha PW50 Dirt Bike.

A cracked fuel line seems trivial until it strands you at the far end of a trail or drips onto a hot pipe. On a 2013 Yamaha PW50, the fuel line is a short, inexpensive piece of rubber doing a job with zero tolerance for failure — and replacing it is well within reach with basic hand tools and about half an hour.

Confirming the Fuel System on Your 2013 Yamaha PW50

Fuel delivery on the 2013 Yamaha PW50 is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.

Warning Signs Your PW50 Needs a New Line

A fuel line rarely fails without hinting first. Run through this list before loading the PW50 up, particularly if the bike has been sitting.

  • Fuel staining at either fitting. Seepage shows up at the barbs before anywhere else.
  • Persistent gasoline smell. If you smell fuel with the bike cold and untouched, something is leaking.
  • Cracks that appear when you flex the hose. Dry rot hides at rest and reveals itself the moment rubber bends.
  • Swelling or a soft, mushy section. The opposite of hardening and just as bad — usually chemical attack.
  • Surging or dying under load. Restricted flow mimics fuel starvation and gets misdiagnosed as a jetting problem.

Gathering Parts and Setting Up

Assemble everything first. Once the line is off, you do not want to be driving to the parts store with an open fuel system.

  • Replacement fuel line in the correct inside diameter and length for your 2013 Yamaha PW50. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.

Why Fuel Lines Harden, Crack, and Fail

It helps to treat fuel line as a consumable rather than a permanent part. The material is engineered to stay soft and seal against a barbed fitting, and it loses that ability gradually as heat cycling, sun exposure, and plain calendar age push it the same direction — a dry climate does it fastest. Fuel chemistry compounds the problem. Ethanol blends sitting through a long off-season absorb water and begin to separate, which is harder on rubber than fresh fuel and leaves gum behind. On a 2013 Yamaha PW50 stored more than ridden, that combination is the usual culprit.

Draining Down and Pulling the Line

Petcock off, first thing. That valve is why a carbureted bike like the PW50 is forgiving here: shut it and the fuel stops moving.

Capture the fuel sitting downstream. Fit a clear hose to the float bowl drain nipple, run it to your container, and open the drain screw a couple of turns. The bowl empties in under a minute. Close the screw afterward, because a bowl that will not hold fuel is frustrating to diagnose later.

Clamps come next. Squeeze the ears of a spring clamp with pliers and slide it clear, or back off a screw clamp until it moves freely. Then persuade the hose off the barb with a twisting motion rather than a hard yank — old rubber bonds to metal, and a straight pull can bend a carburetor inlet or petcock spigot. When the line is truly seized, slice it lengthwise and peel it away.

Getting the New Line Seated Properly

Trim the replacement to the same length as the original. Guessing causes problems at both ends of the range — excess hose finds something hot to lean against, and a short hose loads the fittings every time the engine moves. Cut cleanly and squarely.

Fit the tank-side end first, sliding the hose past the full barb until it bottoms out. If the line is stiff from sitting on a shelf, dip the end in hot water. Do not lubricate: no grease, no oil, no assembly lube on a fuel fitting. Beyond weakening the seal, it introduces contamination into the fuel your PW50 is about to run.

Connect the carburetor end and look at the whole run before securing anything. The hose should mirror the factory routing with clearance from the exhaust and no kinks. Then set both clamps directly over the barbed sections and tighten just enough to compress the rubber. Over-torquing a screw clamp scores the hose and creates a leak path over time.

Confirming It Is Sealed

Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.

Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.

Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our general guide to replacing a dirt bike fuel line.

Related Shopping Categories

Shop Fuel Lines for a 2013 Yamaha PW50 Dirt Bike.

Shop Fuel Line Clamps for a 2013 Yamaha PW50 Dirt Bike.

Shop Petcocks for a 2013 Yamaha PW50 Dirt Bike.

Shop Fuel Filters for a 2013 Yamaha PW50 Dirt Bike.

Shop Fuel Stabilizer for a 2013 Yamaha PW50 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.