Getting a Fresh Fuel Line Onto Your 2013 GAS GAS EC250E

Shop parts for a 2013 GAS GAS EC250E Dirt Bike.

Fuel line replacement sits near the top of the high-value, low-difficulty maintenance list on a 2013 GAS GAS EC250E. The hose is short, the fittings are simple, and the payoff is a fuel system you can stop worrying about. What follows covers identifying what you have, spotting a line on its way out, and getting the new one leak-free.

Why This Part Wears Out at All

It helps to treat fuel line as a consumable rather than a permanent part. The material is engineered to stay soft and seal against a barbed fitting, and it loses that ability gradually as heat cycling, sun exposure, and plain calendar age push it the same direction — a dry climate does it fastest. Fuel chemistry compounds the problem. Ethanol blends sitting through a long off-season absorb water and begin to separate, which is harder on rubber than fresh fuel and leaves gum behind. On a 2013 GAS GAS EC250E stored more than ridden, that combination is the usual culprit.

The Carbureted Setup on This EC250E

Before anything comes apart, confirm what you have. The 2013 GAS GAS EC250E is carbureted, identifiable by the petcock threaded into the bottom of the tank and a plain rubber hose running to the carburetor inlet. No fuel pump sits in the circuit and no pressure needs relieving, which removes the most awkward part of this repair.

What a Dying Fuel Line Looks Like

Fuel line problems show up two ways: something you see and smell, or something you feel while riding. Both are worth taking seriously on a EC250E.

  • Evidence on the ground. A drip or dark patch under the bike after it sits overnight.
  • The smell of raw gasoline. Noticeable with the engine cold and unrun.
  • Surface cracking on the hose. Especially at bends and where the line slides over fittings.
  • Weeping under light pressure. Push gently near a fitting and watch for moisture at the joint.
  • Fuel starvation symptoms. Bogging or cutting out as though the tank ran dry when it clearly has not.

What to Have on the Bench

The parts list is short and the tool list shorter. Lay it out before breaking the first connection.

  • Replacement fuel line in the correct inside diameter and length for your 2013 GAS GAS EC250E. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.

Getting the Old Line Out of the Way

Petcock off, first thing. That valve is why a carbureted bike like the EC250E is forgiving here: shut it and the fuel stops moving.

Capture the fuel sitting downstream. Fit a clear hose to the float bowl drain nipple, run it to your container, and open the drain screw a couple of turns. The bowl empties in under a minute. Close the screw afterward, because a bowl that will not hold fuel is frustrating to diagnose later.

Clamps come next. Squeeze the ears of a spring clamp with pliers and slide it clear, or back off a screw clamp until it moves freely. Then persuade the hose off the barb with a twisting motion rather than a hard yank — old rubber bonds to metal, and a straight pull can bend a carburetor inlet or petcock spigot. When the line is truly seized, slice it lengthwise and peel it away.

Fitting the New Line

Measure the replacement against the old line before cutting. Matching the original length keeps routing correct on the EC250E, and a square cut gives the clamp a clean surface to seal against. Trim with a fresh blade rather than dull side cutters.

Slide the hose fully onto the tank-side fitting, past the barb and up against the shoulder. If the rubber resists, soften it in hot water; do not reach for lubricant. Grease or oil on a fuel fitting shows up later as a slow weep and can carry contamination into the carburetor.

Attach the carburetor end and check the shape of the run. The hose should follow the original path with no contact against cylinder or exhaust and no kink where it curves. Install fresh clamps over the fitting area rather than out on bare hose, and tighten only until the rubber is compressed — a screw clamp cranked down hard will eventually cut through.

Leak Check Before You Ride

With the new line in place, open the petcock and stop. Let the 2013 GAS GAS EC250E sit five minutes over a clean surface and use that time to examine both joints under a flashlight. A properly seated hose stays completely dry; anything else needs attention before the wheels turn.

The running test comes second. Fire the engine, let it warm, and look again — expansion and vibration find seals that hold fine cold and still. When you find a weep, resist the urge to overtighten. Disconnect, verify the hose is pushed fully over the barb, and reassemble; that is nearly always the actual problem.

Wrap up by disposing of the drained fuel appropriately and taking another look at the connections after your next ride. On carbureted bikes an inline filter, if fitted, is a serviceable part worth replacing at the same time. For deeper background on keeping fuel lines healthy between seasons, our broader walkthrough on dirt bike fuel line replacement is a useful companion read.

Related Shopping Categories

Shop Fuel Lines for a 2013 GAS GAS EC250E Dirt Bike.

Shop Fuel Line Clamps for a 2013 GAS GAS EC250E Dirt Bike.

Shop Petcocks for a 2013 GAS GAS EC250E Dirt Bike.

Shop Fuel Filters for a 2013 GAS GAS EC250E Dirt Bike.

Shop Fuel Stabilizer for a 2013 GAS GAS EC250E Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.