Swapping the Fuel Line on Your 2013 GAS GAS EC250
Shop parts for a 2013 GAS GAS EC250 Dirt Bike.
If you have owned your 2013 GAS GAS EC250 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.
Confirming the Fuel System on Your 2013 GAS GAS EC250
Before anything comes apart, confirm what you have. The 2013 GAS GAS EC250 is carbureted, identifiable by the petcock threaded into the bottom of the tank and a plain rubber hose running to the carburetor inlet. No fuel pump sits in the circuit and no pressure needs relieving, which removes the most awkward part of this repair.
Understanding How the Line Deteriorates
Rubber fuel line fails for reasons that have little to do with how hard you ride. Age drives it: the plasticizers keeping the hose flexible slowly migrate out, and pliable rubber turns stiff and glassy, so a small flex — bolting the tank down, rocking the bike onto a stand — opens a hairline crack. Dry, hot storage accelerates that, pulling volatiles out faster than a temperate garage would. Ethanol-blended pump fuel left sitting in the hose adds a second mechanism, attacking the inner wall and leaving gum that can flake into the fuel path on a 2013 GAS GAS EC250.
Symptoms Worth Catching Early
A fuel line rarely fails without hinting first. Run through this list before loading the EC250 up, particularly if the bike has been sitting.
- Fuel staining at either fitting. Seepage shows up at the barbs before anywhere else.
- Persistent gasoline smell. If you smell fuel with the bike cold and untouched, something is leaking.
- Cracks that appear when you flex the hose. Dry rot hides at rest and reveals itself the moment rubber bends.
- Swelling or a soft, mushy section. The opposite of hardening and just as bad — usually chemical attack.
- Surging or dying under load. Restricted flow mimics fuel starvation and gets misdiagnosed as a jetting problem.
Tools & Preparation
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 2013 GAS GAS EC250. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
Take the fuel handling seriously. Vapor sinks and spreads, so ventilation matters more than most people assume — work outside or with the door up, and kill any appliance with a standing pilot flame. Keep the drain container closed between pours and wait for the engine to cool.
Getting the Old Line Out of the Way
Turn the petcock to the off position. On the 2013 GAS GAS EC250 this is the valve underneath the tank, and closing it stops fuel at the source. If your petcock has a reserve position, confirm you are fully off rather than on reserve.
Drain what is trapped downstream. The simplest route is the carburetor float bowl drain — run a short hose from the drain nipple into your container, back the screw out, and let the bowl empty. Snug the screw back up afterward so you do not forget it.
Now free the clamps. Spring clamps come off by squeezing the tabs with pliers and sliding the clamp back along the hose; screw clamps need a few turns of a flat driver. With both retracted, twist the hose on the fitting to break the seal, then work it off. Hardened line often resists — a gentle rotating pull beats brute force, and if it truly will not budge, slit the hose lengthwise with a blade and peel it off rather than levering on the fitting.
Getting the New Line Seated Properly
Measure the replacement against the old line before cutting. Matching the original length keeps routing correct on the EC250, and a square cut gives the clamp a clean surface to seal against. Trim with a fresh blade rather than dull side cutters.
Slide the hose fully onto the tank-side fitting, past the barb and up against the shoulder. If the rubber resists, soften it in hot water; do not reach for lubricant. Grease or oil on a fuel fitting shows up later as a slow weep and can carry contamination into the carburetor.
Attach the carburetor end and check the shape of the run. The hose should follow the original path with no contact against cylinder or exhaust and no kink where it curves. Install fresh clamps over the fitting area rather than out on bare hose, and tighten only until the rubber is compressed — a screw clamp cranked down hard will eventually cut through.
Confirming It Is Sealed
Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.
Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.
Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our broader walkthrough on dirt bike fuel line replacement.
Related Shopping Categories
Shop Fuel Lines for a 2013 GAS GAS EC250 Dirt Bike.
Shop Fuel Line Clamps for a 2013 GAS GAS EC250 Dirt Bike.
Shop Petcocks for a 2013 GAS GAS EC250 Dirt Bike.
Shop Fuel Filters for a 2013 GAS GAS EC250 Dirt Bike.
Shop Fuel Stabilizer for a 2013 GAS GAS EC250 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.