Fuel Line Replacement on the 2010 Yamaha TW200
Shop parts for a 2010 Yamaha TW200 Dirt Bike.
Rubber fuel hose is among the cheapest parts on a 2010 Yamaha TW200 and one of the few that can end a ride outright. It hardens, cracks, and weeps fuel where you cannot see it, eventually either starving the engine or putting gasoline somewhere it should never be. Swapping it needs no specialty tools and no shop time.
The Carbureted Setup on This TW200
Before anything comes apart, confirm what you have. The 2010 Yamaha TW200 is carbureted, identifiable by the petcock threaded into the bottom of the tank and a plain rubber hose running to the carburetor inlet. No fuel pump sits in the circuit and no pressure needs relieving, which removes the most awkward part of this repair.
Red Flags During a Pre-Ride Look
Fuel line problems show up two ways: something you see and smell, or something you feel while riding. Both are worth taking seriously on a TW200.
- Evidence on the ground. A drip or dark patch under the bike after it sits overnight.
- The smell of raw gasoline. Noticeable with the engine cold and unrun.
- Surface cracking on the hose. Especially at bends and where the line slides over fittings.
- Weeping under light pressure. Push gently near a fitting and watch for moisture at the joint.
- Fuel starvation symptoms. Bogging or cutting out as though the tank ran dry when it clearly has not.
Why Fuel Lines Harden, Crack, and Fail
The failure is chemical and thermal more than mechanical. Fuel hose stays soft because of additives in the rubber, and those additives leave over time — faster in heat, faster still in the dry air of an arid climate. A hose in that state has lost its ability to seal around a barb, so it seeps before it visibly splits. Fuel left standing does its own damage: ethanol blends draw in moisture and degrade after months of sitting, and the byproducts attack rubber and leave sticky residue. If your 2010 Yamaha TW200 winters with fuel in the system, the line ages on the calendar rather than the odometer.
Parts, Tools, and a Safe Workspace
The parts list is short and the tool list shorter. Lay it out before breaking the first connection.
- Replacement fuel line in the correct inside diameter and length for your 2010 Yamaha TW200. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
Before the first fitting comes loose, handle the safety side. Gasoline vapor pools low and finds ignition sources you would never consider, including pilot lights across the room. Ventilate properly, keep fuel in a closed container, wear eye protection, and never open the system on a hot engine.
Getting the Old Line Out of the Way
Turn the petcock to the off position. On the 2010 Yamaha TW200 this is the valve underneath the tank, and closing it stops fuel at the source. If your petcock has a reserve position, confirm you are fully off rather than on reserve.
Drain what is trapped downstream. The simplest route is the carburetor float bowl drain — run a short hose from the drain nipple into your container, back the screw out, and let the bowl empty. Snug the screw back up afterward so you do not forget it.
Now free the clamps. Spring clamps come off by squeezing the tabs with pliers and sliding the clamp back along the hose; screw clamps need a few turns of a flat driver. With both retracted, twist the hose on the fitting to break the seal, then work it off. Hardened line often resists — a gentle rotating pull beats brute force, and if it truly will not budge, slit the hose lengthwise with a blade and peel it off rather than levering on the fitting.
Getting the New Line Seated Properly
Measure the replacement against the old line before cutting. Matching the original length keeps routing correct on the TW200, and a square cut gives the clamp a clean surface to seal against. Trim with a fresh blade rather than dull side cutters.
Slide the hose fully onto the tank-side fitting, past the barb and up against the shoulder. If the rubber resists, soften it in hot water; do not reach for lubricant. Grease or oil on a fuel fitting shows up later as a slow weep and can carry contamination into the carburetor.
Attach the carburetor end and check the shape of the run. The hose should follow the original path with no contact against cylinder or exhaust and no kink where it curves. Install fresh clamps over the fitting area rather than out on bare hose, and tighten only until the rubber is compressed — a screw clamp cranked down hard will eventually cut through.
Verifying the Repair
Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.
Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.
Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our complete overview of dirt bike fuel line service.
Related Shopping Categories
Shop Fuel Lines for a 2010 Yamaha TW200 Dirt Bike.
Shop Fuel Line Clamps for a 2010 Yamaha TW200 Dirt Bike.
Shop Petcocks for a 2010 Yamaha TW200 Dirt Bike.
Shop Fuel Filters for a 2010 Yamaha TW200 Dirt Bike.
Shop Fuel Stabilizer for a 2010 Yamaha TW200 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.