Swapping the Fuel Line on Your 2010 GAS GAS TXT PRO 280

Shop parts for a 2010 GAS GAS TXT PRO 280 Dirt Bike.

Fuel line replacement sits near the top of the high-value, low-difficulty maintenance list on a 2010 GAS GAS TXT PRO 280. The hose is short, the fittings are simple, and the payoff is a fuel system you can stop worrying about. What follows covers identifying what you have, spotting a line on its way out, and getting the new one leak-free.

Start by Tracing the Fuel Path

Before anything comes apart, confirm what you have. The 2010 GAS GAS TXT PRO 280 is carbureted, identifiable by the petcock threaded into the bottom of the tank and a plain rubber hose running to the carburetor inlet. No fuel pump sits in the circuit and no pressure needs relieving, which removes the most awkward part of this repair.

Red Flags During a Pre-Ride Look

A fuel line rarely fails without hinting first. Run through this list before loading the TXT PRO 280 up, particularly if the bike has been sitting.

  • Fuel staining at either fitting. Seepage shows up at the barbs before anywhere else.
  • Persistent gasoline smell. If you smell fuel with the bike cold and untouched, something is leaking.
  • Cracks that appear when you flex the hose. Dry rot hides at rest and reveals itself the moment rubber bends.
  • Swelling or a soft, mushy section. The opposite of hardening and just as bad — usually chemical attack.
  • Surging or dying under load. Restricted flow mimics fuel starvation and gets misdiagnosed as a jetting problem.

Understanding How the Line Deteriorates

Rubber fuel line fails for reasons that have little to do with how hard you ride. Age drives it: the plasticizers keeping the hose flexible slowly migrate out, and pliable rubber turns stiff and glassy, so a small flex — bolting the tank down, rocking the bike onto a stand — opens a hairline crack. Dry, hot storage accelerates that, pulling volatiles out faster than a temperate garage would. Ethanol-blended pump fuel left sitting in the hose adds a second mechanism, attacking the inner wall and leaving gum that can flake into the fuel path on a 2010 GAS GAS TXT PRO 280.

Getting Set Up Before You Start

Nothing here is exotic, but having it within reach before you open the fuel system keeps the job from turning messy.

  • Replacement fuel line in the correct inside diameter and length for your 2010 GAS GAS TXT PRO 280. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

Take the fuel handling seriously. Vapor sinks and spreads, so ventilation matters more than most people assume — work outside or with the door up, and kill any appliance with a standing pilot flame. Keep the drain container closed between pours and wait for the engine to cool.

Draining Down and Pulling the Line

Turn the petcock to the off position. On the 2010 GAS GAS TXT PRO 280 this is the valve underneath the tank, and closing it stops fuel at the source. If your petcock has a reserve position, confirm you are fully off rather than on reserve.

Drain what is trapped downstream. The simplest route is the carburetor float bowl drain — run a short hose from the drain nipple into your container, back the screw out, and let the bowl empty. Snug the screw back up afterward so you do not forget it.

Now free the clamps. Spring clamps come off by squeezing the tabs with pliers and sliding the clamp back along the hose; screw clamps need a few turns of a flat driver. With both retracted, twist the hose on the fitting to break the seal, then work it off. Hardened line often resists — a gentle rotating pull beats brute force, and if it truly will not budge, slit the hose lengthwise with a blade and peel it off rather than levering on the fitting.

Installing the Replacement Hose

Use the removed hose as your measuring stick and cut the new one to match. On a 2010 GAS GAS TXT PRO 280 the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.

Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.

Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.

Verifying the Repair

Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.

Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.

Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our general guide to replacing a dirt bike fuel line.

Related Shopping Categories

Shop Fuel Lines for a 2010 GAS GAS TXT PRO 280 Dirt Bike.

Shop Fuel Line Clamps for a 2010 GAS GAS TXT PRO 280 Dirt Bike.

Shop Petcocks for a 2010 GAS GAS TXT PRO 280 Dirt Bike.

Shop Fuel Filters for a 2010 GAS GAS TXT PRO 280 Dirt Bike.

Shop Fuel Stabilizer for a 2010 GAS GAS TXT PRO 280 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.