Replacing the Fuel Line on a 2006 GAS GAS EC125

Shop parts for a 2006 GAS GAS EC125 Dirt Bike.

If you have owned your 2006 GAS GAS EC125 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.

Red Flags During a Pre-Ride Look

Catching a bad line early is mostly about paying attention during routine checks. On a 2006 GAS GAS EC125, these signals should send you looking at the hose.

  • Wet spots on the frame or cases. Fuel evaporates fast, so look for residue rather than liquid.
  • Fuel odor that will not clear. A leak too small to see is still large enough to smell.
  • Hairline splits near the clamps. The clamped section takes the most stress and cracks first.
  • Hose that holds its bend. If the line refuses to straighten, the rubber has hardened.
  • Symptoms resembling a fueling fault. Bogging on hills or running lean with a full tank.

Confirming the Fuel System on Your 2006 GAS GAS EC125

Fuel delivery on the 2006 GAS GAS EC125 is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.

Why This Part Wears Out at All

The failure is chemical and thermal more than mechanical. Fuel hose stays soft because of additives in the rubber, and those additives leave over time — faster in heat, faster still in the dry air of an arid climate. A hose in that state has lost its ability to seal around a barb, so it seeps before it visibly splits. Fuel left standing does its own damage: ethanol blends draw in moisture and degrade after months of sitting, and the byproducts attack rubber and leave sticky residue. If your 2006 GAS GAS EC125 winters with fuel in the system, the line ages on the calendar rather than the odometer.

Getting Set Up Before You Start

Assemble everything first. Once the line is off, you do not want to be driving to the parts store with an open fuel system.

  • Replacement fuel line in the correct inside diameter and length for your 2006 GAS GAS EC125. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

Before the first fitting comes loose, handle the safety side. Gasoline vapor pools low and finds ignition sources you would never consider, including pilot lights across the room. Ventilate properly, keep fuel in a closed container, wear eye protection, and never open the system on a hot engine.

Taking the Failed Hose Off

Close the petcock. Everything downstream of that valve is the only fuel you need to deal with, which on a 2006 GAS GAS EC125 amounts to a few ounces in the line and float bowl.

Get that remaining fuel into a container rather than onto the floor. The float bowl drain screw is purpose-built for this — slip a hose over the nipple, aim it into your catch can, and crack the screw open. If you would rather drain the whole tank, do it now with the hose routed into the container.

Then release both clamps and work the hose off the fittings. Pliers handle spring clamps; a flat screwdriver handles screw clamps. Slide each clamp well back so it cannot fight you. To separate a stubborn hose from a barb, rotate it a quarter turn to shear the bond before pulling. If the rubber has gone hard enough that it will not release, split it with a knife along its length — the hose is being replaced anyway, and the fittings are what matter.

Fitting the New Line

Use the removed hose as your measuring stick and cut the new one to match. On a 2006 GAS GAS EC125 the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.

Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.

Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.

Leak Check Before You Ride

Open the fuel valve and let gravity do the testing. Give the EC125 a few minutes standing over clean cardboard, then inspect the tank-side and carburetor-side joints carefully. Wipe each dry first so new moisture is unmistakable.

Follow that with a running check. Start the engine, bring it to temperature, and look at both fittings again at idle — some leaks only appear once heat and vibration are in the system. A joint weeping under those conditions has a seating problem, not a clamp problem; pull it apart and push the hose fully home.

Then clean up and stay attentive for a ride or two. Dispose of old fuel properly, watch the clamps as the new rubber settles, and consider replacing an inline filter while the system is open. Anyone wanting more detail on what shortens fuel line life long term will find it in our broader walkthrough on dirt bike fuel line replacement.

Related Shopping Categories

Shop Fuel Lines for a 2006 GAS GAS EC125 Dirt Bike.

Shop Fuel Line Clamps for a 2006 GAS GAS EC125 Dirt Bike.

Shop Petcocks for a 2006 GAS GAS EC125 Dirt Bike.

Shop Fuel Filters for a 2006 GAS GAS EC125 Dirt Bike.

Shop Fuel Stabilizer for a 2006 GAS GAS EC125 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.