How the Fuel Line Comes Off and Goes Back On — 2004 Cobra CM50

Shop parts for a 2004 Cobra CM50 Dirt Bike.

If you have owned your 2004 Cobra CM50 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.

Know the CM50 Fuel Layout First

The fuel system on your 2004 Cobra CM50 uses a carburetor, and the petcock is your shutoff. Fuel flows by gravity alone from tank to float bowl through one hose, secured at each end by a spring pinch clamp or a small screw clamp. That is the whole circuit, and it is why this job is beginner-friendly on a two-stroke machine.

Understanding How the Line Deteriorates

Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 2004 Cobra CM50 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.

What a Dying Fuel Line Looks Like

A fuel line rarely fails without hinting first. Run through this list before loading the CM50 up, particularly if the bike has been sitting.

  • Fuel staining at either fitting. Seepage shows up at the barbs before anywhere else.
  • Persistent gasoline smell. If you smell fuel with the bike cold and untouched, something is leaking.
  • Cracks that appear when you flex the hose. Dry rot hides at rest and reveals itself the moment rubber bends.
  • Swelling or a soft, mushy section. The opposite of hardening and just as bad — usually chemical attack.
  • Surging or dying under load. Restricted flow mimics fuel starvation and gets misdiagnosed as a jetting problem.

Gathering Parts and Setting Up

Nothing here is exotic, but having it within reach before you open the fuel system keeps the job from turning messy.

  • Replacement fuel line in the correct inside diameter and length for your 2004 Cobra CM50. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

Before the first fitting comes loose, handle the safety side. Gasoline vapor pools low and finds ignition sources you would never consider, including pilot lights across the room. Ventilate properly, keep fuel in a closed container, wear eye protection, and never open the system on a hot engine.

Getting the Old Line Out of the Way

Turn the petcock to the off position. On the 2004 Cobra CM50 this is the valve underneath the tank, and closing it stops fuel at the source. If your petcock has a reserve position, confirm you are fully off rather than on reserve.

Drain what is trapped downstream. The simplest route is the carburetor float bowl drain — run a short hose from the drain nipple into your container, back the screw out, and let the bowl empty. Snug the screw back up afterward so you do not forget it.

Now free the clamps. Spring clamps come off by squeezing the tabs with pliers and sliding the clamp back along the hose; screw clamps need a few turns of a flat driver. With both retracted, twist the hose on the fitting to break the seal, then work it off. Hardened line often resists — a gentle rotating pull beats brute force, and if it truly will not budge, slit the hose lengthwise with a blade and peel it off rather than levering on the fitting.

Fitting the New Line

Use the removed hose as your measuring stick and cut the new one to match. On a 2004 Cobra CM50 the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.

Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.

Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.

Final Checks and the First Start

Restore fuel flow and watch. Open the petcock on your 2004 Cobra CM50 and leave the bike sitting several minutes with clean cardboard underneath. Gravity finds a poor seal quickly. Look at both fittings with good light, and run a dry fingertip around each joint — fuel is easier to feel than to see.

Then start the engine and check again warm. Vibration and heat expose leaks a static test misses. If you see weeping at a clamp, do not simply crank it tighter; pull the joint apart and confirm the hose was fully seated on the barb, because an unseated hose will not seal at any clamp torque.

Finally, tidy up. Dispose of drained fuel properly rather than returning it to the tank if it looks cloudy or smells stale, and check the new hose after your first ride or two — new rubber takes a small set as it conforms to the fitting. For more background on how fuel quality and storage habits shorten hose life, our general guide to replacing a dirt bike fuel line covers that ground in detail.

Related Shopping Categories

Shop Fuel Lines for a 2004 Cobra CM50 Dirt Bike.

Shop Fuel Line Clamps for a 2004 Cobra CM50 Dirt Bike.

Shop Petcocks for a 2004 Cobra CM50 Dirt Bike.

Shop Fuel Filters for a 2004 Cobra CM50 Dirt Bike.

Shop Fuel Stabilizer for a 2004 Cobra CM50 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.