Getting a Fresh Fuel Line Onto Your 2000 KTM 520SX

Shop parts for a 2000 KTM 520SX Dirt Bike.

Rubber fuel hose is among the cheapest parts on a 2000 KTM 520SX and one of the few that can end a ride outright. It hardens, cracks, and weeps fuel where you cannot see it, eventually either starving the engine or putting gasoline somewhere it should never be. Swapping it needs no specialty tools and no shop time.

The Carbureted Setup on This 520SX

The 2000 KTM 520SX runs a carbureted fuel system, which works in your favor. Fuel leaves the tank through a petcock — the small valve underneath — travels down a short rubber hose, and enters the carburetor at the float bowl inlet. You can shut fuel off at the source, and the line is a simple two-clamp affair with no pump pressure behind it.

Understanding How the Line Deteriorates

It helps to treat fuel line as a consumable rather than a permanent part. The material is engineered to stay soft and seal against a barbed fitting, and it loses that ability gradually as heat cycling, sun exposure, and plain calendar age push it the same direction — a dry climate does it fastest. Fuel chemistry compounds the problem. Ethanol blends sitting through a long off-season absorb water and begin to separate, which is harder on rubber than fresh fuel and leaves gum behind. On a 2000 KTM 520SX stored more than ridden, that combination is the usual culprit.

What a Dying Fuel Line Looks Like

Catching a bad line early is mostly about paying attention during routine checks. On a 2000 KTM 520SX, these signals should send you looking at the hose.

  • Wet spots on the frame or cases. Fuel evaporates fast, so look for residue rather than liquid.
  • Fuel odor that will not clear. A leak too small to see is still large enough to smell.
  • Hairline splits near the clamps. The clamped section takes the most stress and cracks first.
  • Hose that holds its bend. If the line refuses to straighten, the rubber has hardened.
  • Symptoms resembling a fueling fault. Bogging on hills or running lean with a full tank.

What to Have on the Bench

Nothing here is exotic, but having it within reach before you open the fuel system keeps the job from turning messy.

  • Replacement fuel line in the correct inside diameter and length for your 2000 KTM 520SX. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

One genuine safety note: gasoline vapor is heavier than air and travels along the floor toward anything that can ignite it. Work outdoors or with the door open, shut off any heater with a pilot light, keep the fuel container capped, and let a hot engine cool first.

Getting the Old Line Out of the Way

Petcock off, first thing. That valve is why a carbureted bike like the 520SX is forgiving here: shut it and the fuel stops moving.

Capture the fuel sitting downstream. Fit a clear hose to the float bowl drain nipple, run it to your container, and open the drain screw a couple of turns. The bowl empties in under a minute. Close the screw afterward, because a bowl that will not hold fuel is frustrating to diagnose later.

Clamps come next. Squeeze the ears of a spring clamp with pliers and slide it clear, or back off a screw clamp until it moves freely. Then persuade the hose off the barb with a twisting motion rather than a hard yank — old rubber bonds to metal, and a straight pull can bend a carburetor inlet or petcock spigot. When the line is truly seized, slice it lengthwise and peel it away.

Routing and Securing the New Line

Cut the new hose to length using the old one as a template, adding nothing extra. Line that is too long sags into the engine or gets pinched when the tank is bolted down; too short and it tugs at the fittings under vibration. A clean square cut seals better than a ragged one.

Push the new line onto the petcock spigot first, far enough to cover the full barb. Stiff hose goes on more easily after thirty seconds in warm water. What you must not do is lubricate the fitting — no grease, no oil, no silicone. Any of it compromises the seal and can contaminate the fuel path on your 2000 KTM 520SX.

Position the carburetor end next, checking your routing against how the original sat. Then set the clamps over the barb area, about a quarter inch from the hose end, so they compress rubber against the raised portion of the fitting. Snug is the target with screw clamps, not tight — overtightening cuts into the hose and creates the leak you were preventing.

Final Checks and the First Start

With the new line in place, open the petcock and stop. Let the 2000 KTM 520SX sit five minutes over a clean surface and use that time to examine both joints under a flashlight. A properly seated hose stays completely dry; anything else needs attention before the wheels turn.

The running test comes second. Fire the engine, let it warm, and look again — expansion and vibration find seals that hold fine cold and still. When you find a weep, resist the urge to overtighten. Disconnect, verify the hose is pushed fully over the barb, and reassemble; that is nearly always the actual problem.

Wrap up by disposing of the drained fuel appropriately and taking another look at the connections after your next ride. On carbureted bikes an inline filter, if fitted, is a serviceable part worth replacing at the same time. For deeper background on keeping fuel lines healthy between seasons, our general guide to replacing a dirt bike fuel line is a useful companion read.

Related Shopping Categories

Shop Fuel Lines for a 2000 KTM 520SX Dirt Bike.

Shop Fuel Line Clamps for a 2000 KTM 520SX Dirt Bike.

Shop Petcocks for a 2000 KTM 520SX Dirt Bike.

Shop Fuel Filters for a 2000 KTM 520SX Dirt Bike.

Shop Fuel Stabilizer for a 2000 KTM 520SX Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.