How the Fuel Line Comes Off and Goes Back On — 1980 Yamaha IT250

Shop parts for a 1980 Yamaha IT250 Dirt Bike.

If you have owned your 1980 Yamaha IT250 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.

Symptoms Worth Catching Early

Fuel line problems show up two ways: something you see and smell, or something you feel while riding. Both are worth taking seriously on a IT250.

  • Evidence on the ground. A drip or dark patch under the bike after it sits overnight.
  • The smell of raw gasoline. Noticeable with the engine cold and unrun.
  • Surface cracking on the hose. Especially at bends and where the line slides over fittings.
  • Weeping under light pressure. Push gently near a fitting and watch for moisture at the joint.
  • Fuel starvation symptoms. Bogging or cutting out as though the tank ran dry when it clearly has not.

Why Rubber Fuel Hose Gives Up

It helps to treat fuel line as a consumable rather than a permanent part. The material is engineered to stay soft and seal against a barbed fitting, and it loses that ability gradually as heat cycling, sun exposure, and plain calendar age push it the same direction — a dry climate does it fastest. Fuel chemistry compounds the problem. Ethanol blends sitting through a long off-season absorb water and begin to separate, which is harder on rubber than fresh fuel and leaves gum behind. On a 1980 Yamaha IT250 stored more than ridden, that combination is the usual culprit.

Know the IT250 Fuel Layout First

The 1980 Yamaha IT250 runs a carbureted fuel system, which works in your favor. Fuel leaves the tank through a petcock — the small valve underneath — travels down a short rubber hose, and enters the carburetor at the float bowl inlet. You can shut fuel off at the source, and the line is a simple two-clamp affair with no pump pressure behind it.

Tools & Preparation

Assemble everything first. Once the line is off, you do not want to be driving to the parts store with an open fuel system.

  • Replacement fuel line in the correct inside diameter and length for your 1980 Yamaha IT250. Match the original rather than guessing — oversized line will not seal on the barb.
  • New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
  • Nitrile or rubber gloves. Gasoline absorbs through skin.
  • A fuel-safe drain container and a funnel if you plan to reuse the fuel.
  • Pliers and a small flat screwdriver for spring and screw clamps respectively.
  • Shop rags and eye protection.

A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.

Removing the Old Fuel Line

Turn the petcock to the off position. On the 1980 Yamaha IT250 this is the valve underneath the tank, and closing it stops fuel at the source. If your petcock has a reserve position, confirm you are fully off rather than on reserve.

Drain what is trapped downstream. The simplest route is the carburetor float bowl drain — run a short hose from the drain nipple into your container, back the screw out, and let the bowl empty. Snug the screw back up afterward so you do not forget it.

Now free the clamps. Spring clamps come off by squeezing the tabs with pliers and sliding the clamp back along the hose; screw clamps need a few turns of a flat driver. With both retracted, twist the hose on the fitting to break the seal, then work it off. Hardened line often resists — a gentle rotating pull beats brute force, and if it truly will not budge, slit the hose lengthwise with a blade and peel it off rather than levering on the fitting.

Getting the New Line Seated Properly

Cut the new hose to length using the old one as a template, adding nothing extra. Line that is too long sags into the engine or gets pinched when the tank is bolted down; too short and it tugs at the fittings under vibration. A clean square cut seals better than a ragged one.

Push the new line onto the petcock spigot first, far enough to cover the full barb. Stiff hose goes on more easily after thirty seconds in warm water. What you must not do is lubricate the fitting — no grease, no oil, no silicone. Any of it compromises the seal and can contaminate the fuel path on your 1980 Yamaha IT250.

Position the carburetor end next, checking your routing against how the original sat. Then set the clamps over the barb area, about a quarter inch from the hose end, so they compress rubber against the raised portion of the fitting. Snug is the target with screw clamps, not tight — overtightening cuts into the hose and creates the leak you were preventing.

Wrapping Up and Checking Your Work

Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.

Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.

Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our full guide to dirt bike fuel line care.

Related Shopping Categories

Shop Fuel Lines for a 1980 Yamaha IT250 Dirt Bike.

Shop Fuel Line Clamps for a 1980 Yamaha IT250 Dirt Bike.

Shop Petcocks for a 1980 Yamaha IT250 Dirt Bike.

Shop Fuel Filters for a 1980 Yamaha IT250 Dirt Bike.

Shop Fuel Stabilizer for a 1980 Yamaha IT250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.