Swapping the Fuel Line on Your 1979 Yamaha YZ250
Shop parts for a 1979 Yamaha YZ250 Dirt Bike.
If you have owned your 1979 Yamaha YZ250 more than a few seasons, the fuel line deserves a hard look. It is a wear item almost nobody thinks about until it fails, and the failure is rarely graceful. Replacing the hose costs a few dollars, and doing it early beats doing it trailside with a leaking tank.
Why This Part Wears Out at All
Two things degrade a fuel line: time, and what sits inside it. Rubber loses flexibility as it ages, and a hose that spent eight years on a 1979 Yamaha YZ250 has been hardening the whole time, ridden or parked. Hardened rubber cannot absorb vibration, so it cracks where it stretches over a fitting. Ethanol-blended gasoline is the other half — fuel sitting unused for months attracts moisture and breaks down, which is rough on hose material and leaves varnish behind. Add a dry climate baking out what flexibility remains, and a line that looked fine last season can be brittle by spring.
Confirming the Fuel System on Your 1979 Yamaha YZ250
Fuel delivery on the 1979 Yamaha YZ250 is carbureted, so the plumbing is about as simple as it gets on a two-stroke dirt bike — tank, petcock, hose, carburetor. That petcock is the most useful thing about this job. Turn it off and the fuel stops, which means no siphoning and no fighting gravity while you work.
How a Failing Line Announces Itself
Most failing fuel lines warn you before letting go. The warnings are easy to dismiss, so it helps to know what you are looking at when you walk up to your 1979 Yamaha YZ250.
- A puddle or damp patch underneath. Even a slow weep leaves evidence, usually below the tank or carburetor.
- A strong fuel smell in the garage. Odor lingering a day after parking is not normal.
- Visible cracking. Bend the hose gently; fine cracks that open under flex mean the rubber is done.
- A hose that feels hard or glazed. Healthy line is soft and slightly tacky.
- Bogging or running lean. A collapsed or deteriorated line restricts flow, and the engine acts like the tank is nearly empty.
Parts, Tools, and a Safe Workspace
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 1979 Yamaha YZ250. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
A word on handling fuel, because this is the part with real consequences: gasoline vapor is heavier than air and will travel across a floor to any spark or flame. Open the door, shut off pilot lights, cap your container, and let the bike cool. Gloves and eye protection are not optional.
Draining Down and Pulling the Line
Close the petcock. Everything downstream of that valve is the only fuel you need to deal with, which on a 1979 Yamaha YZ250 amounts to a few ounces in the line and float bowl.
Get that remaining fuel into a container rather than onto the floor. The float bowl drain screw is purpose-built for this — slip a hose over the nipple, aim it into your catch can, and crack the screw open. If you would rather drain the whole tank, do it now with the hose routed into the container.
Then release both clamps and work the hose off the fittings. Pliers handle spring clamps; a flat screwdriver handles screw clamps. Slide each clamp well back so it cannot fight you. To separate a stubborn hose from a barb, rotate it a quarter turn to shear the bond before pulling. If the rubber has gone hard enough that it will not release, split it with a knife along its length — the hose is being replaced anyway, and the fittings are what matter.
Routing and Securing the New Line
Use the removed hose as your measuring stick and cut the new one to match. On a 1979 Yamaha YZ250 the correct length stays clear of moving and hot components while still absorbing engine movement without pulling on either fitting. Square off both ends with a sharp blade.
Start at the petcock. Work the hose on until the barb is fully buried — a partial seat is the most common cause of a post-repair leak. Warming a stiff hose helps it slide; lubricating the fitting does not. Leave grease and oil out entirely, since either prevents the rubber gripping properly and can end up inside the carburetor.
Then connect the carburetor side and dry-fit before clamping. Mount the tank if it was removed and verify the hose is not trapped, stretched, or resting on the head. Once the routing looks right, place a clamp at each end over the fitting itself and bring it to snug. New spring clamps are hard to overdo; screw clamps need restraint.
Confirming It Is Sealed
Turn the petcock back on and give it time. Several minutes of sitting over clean cardboard will reveal a gravity leak that a quick glance would not. Inspect both connection points closely, by touch as well as by eye, since a slow weep often shows up as nothing more than dampness at the clamp.
Start it up next. Heat and vibration change the picture, so run the engine to temperature and inspect the joints again at idle. A leak appearing only when running usually means the hose is not seated deeply enough — take it apart and reseat rather than adding clamp tension, which only damages rubber.
Once it passes both tests, finish the housekeeping. Handle the drained fuel responsibly and think twice about reusing it if it has gone stale. Recheck the fittings after the first ride, since a new hose settles onto the barbs. Riders wanting a broader look at fuel line care and storage-related failures will find more in our full guide to dirt bike fuel line care.
Related Shopping Categories
Shop Fuel Lines for a 1979 Yamaha YZ250 Dirt Bike.
Shop Fuel Line Clamps for a 1979 Yamaha YZ250 Dirt Bike.
Shop Petcocks for a 1979 Yamaha YZ250 Dirt Bike.
Shop Fuel Filters for a 1979 Yamaha YZ250 Dirt Bike.
Shop Fuel Stabilizer for a 1979 Yamaha YZ250 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.