How the Fuel Line Comes Off and Goes Back On — 1979 Yamaha IT250
Shop parts for a 1979 Yamaha IT250 Dirt Bike.
Fuel line replacement sits near the top of the high-value, low-difficulty maintenance list on a 1979 Yamaha IT250. The hose is short, the fittings are simple, and the payoff is a fuel system you can stop worrying about. What follows covers identifying what you have, spotting a line on its way out, and getting the new one leak-free.
What You Are Working With on the IT250
Before anything comes apart, confirm what you have. The 1979 Yamaha IT250 is carbureted, identifiable by the petcock threaded into the bottom of the tank and a plain rubber hose running to the carburetor inlet. No fuel pump sits in the circuit and no pressure needs relieving, which removes the most awkward part of this repair.
Symptoms Worth Catching Early
Catching a bad line early is mostly about paying attention during routine checks. On a 1979 Yamaha IT250, these signals should send you looking at the hose.
- Wet spots on the frame or cases. Fuel evaporates fast, so look for residue rather than liquid.
- Fuel odor that will not clear. A leak too small to see is still large enough to smell.
- Hairline splits near the clamps. The clamped section takes the most stress and cracks first.
- Hose that holds its bend. If the line refuses to straighten, the rubber has hardened.
- Symptoms resembling a fueling fault. Bogging on hills or running lean with a full tank.
What Actually Kills a Fuel Line
It helps to treat fuel line as a consumable rather than a permanent part. The material is engineered to stay soft and seal against a barbed fitting, and it loses that ability gradually as heat cycling, sun exposure, and plain calendar age push it the same direction — a dry climate does it fastest. Fuel chemistry compounds the problem. Ethanol blends sitting through a long off-season absorb water and begin to separate, which is harder on rubber than fresh fuel and leaves gum behind. On a 1979 Yamaha IT250 stored more than ridden, that combination is the usual culprit.
Tools & Preparation
This is a low-cost job, and most of the preparation is about containing fuel rather than turning wrenches.
- Replacement fuel line in the correct inside diameter and length for your 1979 Yamaha IT250. Match the original rather than guessing — oversized line will not seal on the barb.
- New clamps. Spring clamps lose tension with age, and a small clamp kit costs very little.
- Nitrile or rubber gloves. Gasoline absorbs through skin.
- A fuel-safe drain container and a funnel if you plan to reuse the fuel.
- Pliers and a small flat screwdriver for spring and screw clamps respectively.
- Shop rags and eye protection.
Before the first fitting comes loose, handle the safety side. Gasoline vapor pools low and finds ignition sources you would never consider, including pilot lights across the room. Ventilate properly, keep fuel in a closed container, wear eye protection, and never open the system on a hot engine.
Removing the Old Fuel Line
Close the petcock. Everything downstream of that valve is the only fuel you need to deal with, which on a 1979 Yamaha IT250 amounts to a few ounces in the line and float bowl.
Get that remaining fuel into a container rather than onto the floor. The float bowl drain screw is purpose-built for this — slip a hose over the nipple, aim it into your catch can, and crack the screw open. If you would rather drain the whole tank, do it now with the hose routed into the container.
Then release both clamps and work the hose off the fittings. Pliers handle spring clamps; a flat screwdriver handles screw clamps. Slide each clamp well back so it cannot fight you. To separate a stubborn hose from a barb, rotate it a quarter turn to shear the bond before pulling. If the rubber has gone hard enough that it will not release, split it with a knife along its length — the hose is being replaced anyway, and the fittings are what matter.
Fitting the New Line
Cut the new hose to length using the old one as a template, adding nothing extra. Line that is too long sags into the engine or gets pinched when the tank is bolted down; too short and it tugs at the fittings under vibration. A clean square cut seals better than a ragged one.
Push the new line onto the petcock spigot first, far enough to cover the full barb. Stiff hose goes on more easily after thirty seconds in warm water. What you must not do is lubricate the fitting — no grease, no oil, no silicone. Any of it compromises the seal and can contaminate the fuel path on your 1979 Yamaha IT250.
Position the carburetor end next, checking your routing against how the original sat. Then set the clamps over the barb area, about a quarter inch from the hose end, so they compress rubber against the raised portion of the fitting. Snug is the target with screw clamps, not tight — overtightening cuts into the hose and creates the leak you were preventing.
Confirming It Is Sealed
With the new line in place, open the petcock and stop. Let the 1979 Yamaha IT250 sit five minutes over a clean surface and use that time to examine both joints under a flashlight. A properly seated hose stays completely dry; anything else needs attention before the wheels turn.
The running test comes second. Fire the engine, let it warm, and look again — expansion and vibration find seals that hold fine cold and still. When you find a weep, resist the urge to overtighten. Disconnect, verify the hose is pushed fully over the barb, and reassemble; that is nearly always the actual problem.
Wrap up by disposing of the drained fuel appropriately and taking another look at the connections after your next ride. On carbureted bikes an inline filter, if fitted, is a serviceable part worth replacing at the same time. For deeper background on keeping fuel lines healthy between seasons, our full guide to dirt bike fuel line care is a useful companion read.
Related Shopping Categories
Shop Fuel Lines for a 1979 Yamaha IT250 Dirt Bike.
Shop Fuel Line Clamps for a 1979 Yamaha IT250 Dirt Bike.
Shop Petcocks for a 1979 Yamaha IT250 Dirt Bike.
Shop Fuel Filters for a 1979 Yamaha IT250 Dirt Bike.
Shop Fuel Stabilizer for a 1979 Yamaha IT250 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.