How to Bleed a Spongy or Stiff Clutch on a 2020 Beta 390 RR-S Dirt Bike

Shop parts for a 2020 Beta 390 RR-S Dirt Bike.

What a Bad Clutch Lever Feels Like

On the 2020 Beta 390 RR-S, the clutch uses a hydraulic system with a master cylinder and reservoir mounted at the handlebar lever and a slave cylinder working at the engine side cover. When the lever is healthy, it has a firm, consistent feel from the first pull to the point where the plates separate. When it goes wrong, the lever may feel soft and squishy, travel farther than it used to before the clutch disengages, or fade a little during a long session in tight enduro terrain. Some riders notice the lever pulling back toward the grip more slowly after repeated pulls, which is another sign that the fluid column is not behaving the way it should.

That feel matters more on this bike than many riders realize. A 390cc four-stroke single produces strong low-end pull, and the clutch has to hold that power cleanly and release it predictably. A spongy lever makes hard motocross starts unpredictable, because you cannot tell exactly where the clutch will bite. In a rocky uphill section, a lever that fades can leave you feeling for engagement at the wrong moment. Through corners, inconsistent release makes it harder to modulate the rear wheel smoothly.

Why the Lever Gets Soft

A soft or inconsistent lever almost always comes down to one of two things: air trapped somewhere in the hydraulic line, or fluid that has aged and lost its ability to transfer pressure cleanly. Air can enter during a fluid change, after a line is disconnected, or through a small leak at a fitting. Over time, moisture and heat also degrade the fluid, and that breakdown shows up as a lever that feels vague or sponges under load.

Hydraulic clutches on dirt bikes are self-adjusting, which means that as the friction plates wear, the slave cylinder and master cylinder account for the change automatically. You do not need to set anything by hand to fix a spongy feel. If the lever still feels wrong after a proper bleed, the cause is almost always in the fluid path rather than in the clutch pack itself.

Choosing the Right Fluid Without Mixing

Some hydraulic clutch systems are designed around mineral oil, while others use brake fluid. The correct type is marked on the reservoir cap or on the master cylinder body, so check there before you open anything. Never mix the two types. They are not chemically compatible, and mixing them can damage seals and cause the system to fail. If you are unsure what is currently in the bike, drain the system completely and refill it with the type shown on the marking before you bleed.

Tools and Preparation

You will need a clean container for old fluid, a small wrench that fits the slave cylinder bleeder, a length of clear tubing that fits snugly over the bleeder nipple, a syringe for pushing fresh fluid, a shop rag, and a fresh bottle of the correct fluid. Keep the fluid sealed until you are ready to use it, since it absorbs moisture from the air.

Protect the paint on the frame, the plastics near the reservoir, and the tank shrouds. Hydraulic fluid strips paint quickly and can leave a cloudy mark on plastics. Lay a rag over anything it might touch and wipe spills immediately with a damp cloth.

Step-by-Step Bleed Procedure

  1. Park the bike on level ground and turn the handlebar so the master cylinder reservoir sits level. A tilted reservoir gives a false fluid level and can trap air.
  2. Remove the reservoir cap and the rubber diaphragm beneath it. Top the reservoir to the upper line with the correct fluid.
  3. Locate the bleeder screw on the slave cylinder at the engine side. Remove its dust cap and clean around it.
  4. Fit the clear tubing over the bleeder nipple and place the other end in your waste container so the tube stays submerged in a small amount of fluid.
  5. Pull the lever slowly, hold it fully pulled, then crack the bleeder open briefly. Close the bleeder before releasing the lever. Repeat this lever-and-bleeder cycle while checking the reservoir level often so it never runs empty.
  6. Once the lever feels firm and the fluid coming through the tube is free of bubbles, close the bleeder and wipe the area clean.
  7. For a more thorough refresh, switch to the reverse-bleed method. Attach the syringe filled with fresh fluid to the bleeder, open the bleeder slightly, and push fluid upward through the slave cylinder and into the line toward the master cylinder. Continue until fresh fluid reaches the reservoir and no bubbles appear in the clear tube.
  8. Release the lever, top the reservoir, reinstall the diaphragm and cap, and recheck the level.

You know the bleed is complete when the lever feels firm from the first pull, returns quickly, and holds its position under steady pressure. The fluid leaving the bleeder should be clear and free of bubbles. Test the lever while the bike is stationary, then start it and engage the clutch briefly to confirm the feel under real pressure.

Checking for Leaks

A bleed will not hold if there is a leak somewhere in the system. Start at the master cylinder, looking around the reservoir base and the lever pivot area for wet spots or residue. Move to the line fittings at both ends of the hose, paying close attention to the banjo bolts and any clamp points where the hose bends sharply. Finally, check the slave cylinder body and its seals at the engine side. A leak at the slave cylinder often appears as fluid running down the case, so look for streaks even if the drip is small. Wipe every surface dry, then watch the lever over a few minutes of pressure to confirm nothing is seeping.

Once the system is sealed and bled, pay attention to how the lever behaves over the next few rides. A clean, firm feel that stays consistent through hard starts and tight trail sections is the result you are looking for. If the lever goes soft again quickly, the leak check should be repeated before anything else is considered.

Related Shopping Categories

Shop Cables for a 2020 Beta 390 RR-S Dirt Bike.

Shop Levers for a 2020 Beta 390 RR-S Dirt Bike.

Shop Brake Bleeders for a 2020 Beta 390 RR-S Dirt Bike.

Shop Clutch Kits for a 2020 Beta 390 RR-S Dirt Bike.

Shop Tools for a 2020 Beta 390 RR-S Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.