How to Fix a Spongy or Stiff Clutch on a 2017 GAS GAS EC300 Dirt Bike
Shop parts for a 2017 GAS GAS EC300 Dirt Bike.
A clutch lever that feels wrong on the 2017 GAS GAS EC300 is easy to notice once you know what to look for. A spongy lever travels too far before it bites, or it feels squishy under your fingers. A stiff lever takes real effort to pull and may feel notchy or sticky. Either problem affects how cleanly the bike launches out of a gate, how smoothly you modulate power through a tight enduro switchback, and how confidently you can hold a line through a corner. This 300cc two-stroke is quick to respond, so a clutch that does not return or release consistently can make the whole bike feel unpredictable. The good news is that most of these symptoms come from simple, garage-level causes.
Confirming Which Clutch System Your Bike Uses
Before you pull anything apart, take a look at the clutch side of the handlebar. A small fluid reservoir mounted on the clutch perch means the bike uses a hydraulic clutch. A cable running from the lever down toward the engine means the bike uses a cable-operated clutch. Identify which one you have, then jump to the matching section below. Both systems are maintained differently, so following the wrong procedure will not solve the problem.
Servicing a Hydraulic Clutch
A hydraulic clutch uses a master cylinder and reservoir at the lever and a slave cylinder mounted at the engine, connected by a line filled with fluid. When the lever feels spongy, soft, or inconsistent from pull to pull, the most common culprits are air trapped somewhere in the system or fluid that has aged and lost its performance. Heat from hard motocross starts and long, clutch-heavy enduro sections breaks down fluid over time, so a refresh and bleed is the standard fix.
Some hydraulic clutches use mineral oil and others use brake fluid. The correct type is printed on the reservoir cap or the master cylinder body. Check it before you open anything, and never mix the two, because they are not compatible and mixing them can damage seals.
To refresh and bleed the system, work through these steps:
- Park the bike on level ground and turn the handlebar so the reservoir sits level. A tilted reservoir gives a false fluid reading and can pull air into the master cylinder.
- Cover the tank, levers, and nearby plastics with a rag. Spilled fluid can dull paint and cloud plastic quickly.
- Remove the reservoir cap and diaphragm, then drain the old fluid from the reservoir and clean the inside with a clean, lint-free cloth.
- Locate the bleeder screw on the slave cylinder at the engine side and fit a clear hose over it, with the other end running into a catch container.
- Refill the reservoir with fresh fluid of the correct type. Open the bleeder slightly and use the lever-and-bleeder method: pump the lever slowly, hold it squeezed, close the bleeder, then release. Repeat until fresh fluid flows out with no bubbles.
- For stubborn air, use the reverse-bleed method. Attach a syringe filled with fresh fluid to the slave cylinder bleeder and gently push fluid upward toward the master cylinder until the lever feels firm.
- Top the reservoir to the marked level, reinstall the diaphragm and cap, and test the lever several times.
You know the bleed is complete when the lever feels firm and consistent from the first pull to the last, and when the fluid coming out of the bleeder is free of bubbles. Check for leaks at the master cylinder, the slave cylinder, and every line fitting while the lever is squeezed. Look for wet spots, seepage around fittings, or a slowly dropping reservoir level. Tighten any loose fitting carefully and wipe everything dry before a test ride. Hydraulic clutches are self-adjusting, so once the system is bled and sealed, the lever should feel consistent without any further adjustment work.
Servicing a Cable-Operated Clutch
A cable-operated clutch is a different story. A stiff, notchy, sticky, or heavy lever usually comes from a dry, dirty, frayed, or kinked cable, or from a dry lever pivot. Those problems are common on a two-stroke that sees mud, sand, and water, and they become more noticeable after a long moto or a rainy enduro day.
Work through these steps:
- Inspect the cable along its full length, paying special attention to both ends where it enters the lever and the engine side. Look for fraying, flattened strands, or a sheath that has split.
- Follow the routing from the lever to the engine and check for kinks and tight bends. Any sharp bend that pinches the cable will make the lever heavy, so reroute it to a gentler curve and secure it with the existing clips.
- Lubricate the lever pivot with a light lubricant, working it through the pivot until the lever returns smoothly on its own.
- Disconnect the cable at both ends, clean out dirt with a degreaser and a rag, then lubricate the inner cable and reinstall it. Pull it through a few times to spread the lubricant evenly.
- Replace the cable if you find fraying, a kink, or a sheath that remains stiff after lubrication. A new cable is inexpensive compared with the riding time lost to a sticky lever.
If the lever feels soft or vague rather than stiff, the cause is usually excessive freeplay or a stretched cable. Freeplay is set separately during clutch adjustment, so a soft lever is a reason to check how the cable is seated and whether it has stretched, not a reason to start guessing at settings. A worn cable that has stretched will not hold its feel and should be replaced.
Whichever system your 2017 GAS GAS EC300 uses, a careful inspection and a methodical service will restore a clutch lever you can trust on the start line, through the whoops, and in the tight sections where clean engagement matters most.
Related Shopping Categories
Shop Cables for a 2017 GAS GAS EC300 Dirt Bike.
Shop Levers for a 2017 GAS GAS EC300 Dirt Bike.
Shop Brake Bleeders for a 2017 GAS GAS EC300 Dirt Bike.
Shop Clutch Kits for a 2017 GAS GAS EC300 Dirt Bike.
Shop Tools for a 2017 GAS GAS EC300 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.