How to Fix a Spongy or Stiff Clutch on a 2015 Beta 390 RS Dirt Bike
Shop parts for a 2015 Beta 390 RS Dirt Bike.
What a Spongy Lever Feels Like on the 390 RS
A spongy clutch lever on the 2015 Beta 390 RS has a distinct character. The lever pulls in with little resistance, then feels squishy or elastic near the end of its travel. Some riders notice the engagement point shifting from ride to ride, while others find the lever pulls all the way to the bar without the clutch fully disengaging. On a 390cc four-stroke, that inconsistency shows up quickly in tight enduro sections where you are feathering the clutch over roots and rocks, and in motocross starts where a vague lever makes it hard to meter the power off the line.
This bike uses a hydraulic clutch. A master cylinder and reservoir sit at the handlebar on the clutch perch, and a slave cylinder mounts at the engine side, pushing the plates apart when you squeeze the lever. Because the whole system is a sealed column of fluid, anything that compromises that column changes how the lever feels.
Why Air and Old Fluid Cause the Problem
In most cases, a spongy or inconsistent lever comes down to air trapped somewhere in the line or fluid that has aged and absorbed moisture. Air compresses under load, so every squeeze of the lever is partly absorbed by the bubbles instead of being transferred to the slave cylinder. Old fluid can also lose its performance over time, especially on a bike that sees hot trail rides, long enduro days, or repeated hard clutch work during motocross sessions.
Some hydraulic clutches are designed to use mineral oil, while others use brake fluid. The correct type is marked on the reservoir cap or the master cylinder body. Check that marking before you do anything else. The two fluid types must never be mixed, because they are not chemically compatible and mixing them can damage seals and lead to a system that performs poorly or fails outright.
Gathering Your Tools and Setting Up the Bike
You do not need specialty equipment for this job. A clean bleed bottle or a small clear hose that fits the slave cylinder bleeder, a wrench to fit that bleeder, a syringe for pushing fluid, shop rags, and a fresh bottle of the correct fluid will cover everything. Protect the bodywork and painted surfaces around the reservoir with a rag or painter’s tape, since fluid will strip paint and damage plastic.
Park the bike on level ground and turn the handlebar so the reservoir sits level. A tilted reservoir gives a false reading on fluid level and can pull air into the master cylinder during the procedure.
Step-by-Step Bleed Procedure
- Remove the reservoir cap and the rubber diaphragm beneath it. Top the reservoir with fresh fluid, keeping the level near the upper mark throughout the job.
- Locate the bleeder screw on the slave cylinder at the engine side. Remove the dust cap and fit your clear hose over the bleeder, routing the other end into a catch container.
- Squeeze the lever slowly, hold it, then open the bleeder about a quarter turn. Watch for fluid and bubbles moving through the hose, then close the bleeder before releasing the lever. Repeat until no bubbles appear.
- For the reverse-bleed method, fill a syringe with fresh fluid, attach it to the bleeder, and gently push fluid up through the slave cylinder toward the reservoir. Open the reservoir side as needed so trapped air can escape upward. This is especially helpful when the lever is very spongy and the standard lever-and-bleeder method struggles to clear the air.
- Keep the reservoir topped up at all times. Letting it run low pulls new air into the system and undoes your progress.
- Once the lever feels firm and consistent from the first inch of travel to the point of full release, and the fluid leaving the hose is free of bubbles, close the bleeder, reinstall the dust cap, and refit the diaphragm and reservoir cap.
Checking for Leaks Before You Ride
After bleeding, inspect the entire system closely. Look at the master cylinder body and the base of the reservoir for seepage, check the banjo fittings and line connections at both ends, and examine the slave cylinder body and bleeder threads. A small leak can be hard to see when the bike is dry, so wipe each fitting clean, work the lever a few times, and look again for fresh wetness. Any leak at a fitting usually means the connection needs to be snugged or the washer replaced.
Self-Adjusting Behavior and Lever Feel
Hydraulic clutches on the 390 RS are self-adjusting, so once the system is clean and free of air, you should not need to make any mechanical changes to get consistent engagement. If the lever still feels inconsistent after a thorough bleed and a leak check, recheck the fluid level and the condition of the fluid itself. Dark or cloudy fluid suggests it is time for a full refresh rather than a quick top-off.
A well-bled clutch on this bike gives a firm, predictable lever that lets you find the friction zone easily, whether you are leaving a start gate, picking a line through a log crossing, or working through a tight switchback on a long trail ride. Taking the time to do the job right makes every clutch input more precise.
Related Shopping Categories
Shop Cables for a 2015 Beta 390 RS Dirt Bike.
Shop Levers for a 2015 Beta 390 RS Dirt Bike.
Shop Brake Bleeders for a 2015 Beta 390 RS Dirt Bike.
Shop Clutch Kits for a 2015 Beta 390 RS Dirt Bike.
Shop Tools for a 2015 Beta 390 RS Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.