How to Bleed a Spongy or Stiff Clutch on a 2013 Beta 520 RS SM Dirt Bike
Shop parts for a 2013 Beta 520 RS SM Dirt Bike.
What a Spongy Lever Feels Like on the 520 RS SM
The 2013 Beta 520 RS SM uses a hydraulic clutch, with a master cylinder and reservoir mounted at the left handlebar and a slave cylinder working the clutch pack at the engine. When the system is healthy, the lever has a firm, consistent feel from the first pull to the point where the clutch disengages. A spongy lever is different. It travels further than expected before any resistance builds, it may feel mushy or inconsistent from pull to pull, and the engagement point can wander from one ride to the next. Some riders notice it most during slow technical climbs, where they find themselves feathering the lever without knowing exactly where the bite begins.
Why Air and Old Fluid Cause the Problem
In nearly every case, a soft or inconsistent lever comes down to air in the hydraulic line or fluid that has aged and lost its ability to transmit pressure cleanly. Air compresses, so every squeeze of the lever is partly absorbed by bubbles rather than moving the slave cylinder. Old fluid can also collect moisture over time, which further undermines feel. Hard starts from a gate, repeated clutch slipping on loose terrain, and long enduro days in heat all put extra stress on the system and can accelerate the decline. The fix is a fluid refresh followed by a full bleed.
Know Your Fluid Before You Start
Hydraulic clutches are not all filled the same way. Some use mineral oil, while others rely on brake fluid. The correct type is marked on the reservoir cap or stamped near the master cylinder body, so check there before opening anything. Never mix the two. Introducing the wrong fluid can swell seals, damage internal components, and leave you with a lever that feels worse than when you started. Keep the fluid you are removing separate from the new supply, and wipe any residue from the cap area before it has a chance to fall into the reservoir.
Tools and Preparation
You will need a clean container for old fluid, a fresh bottle of the correct fluid, a bleeder wrench that fits the slave cylinder bleeder, a short length of clear tubing that fits snugly over the bleeder nipple, and a syringe for the reverse method. Shop rags are essential. Place a towel under the handlebar and along the front of the engine cases to protect plastics and paint, since clutch fluid is a strong solvent for many finishes. Position the bike upright on a level surface, and turn the bars so the reservoir sits level rather than tilted. A tilted reservoir can trap air pockets that never fully clear.
Step-by-Step Bleed Procedure
- Level the reservoir, then remove the cap and rubber diaphragm carefully, keeping both clean and free of debris.
- Top the reservoir with fresh fluid, filling to the mark rather than to the rim.
- Locate the bleeder screw on the slave cylinder at the engine side. Remove the dust cover and clean the area around the bleeder.
- Attach the clear tubing to the bleeder nipple and route the free end into your waste container.
- Pump the lever slowly several times, then hold it firmly squeezed. Open the bleeder a quarter turn and watch the fluid flow into the tube. Close the bleeder before releasing the lever.
- Repeat the squeeze, hold, open, and close cycle until the fluid runs clear with no bubbles visible in the tube.
- Check the reservoir level frequently during the process so air is not drawn back into the system.
The Reverse Bleed Method
If the lever still feels soft after a standard bleed, try reverse bleeding. Fill a syringe with fresh fluid and attach it to the slave cylinder bleeder using the tubing. Open the bleeder slightly and gently push fresh fluid upward through the line toward the master cylinder. This pushes trapped air up and out through the reservoir. Keep the reservoir topped up as you work, and stop once you see clean fluid with no bubbles rising. Reinstall the diaphragm and cap once the reservoir has settled.
Confirming the Bleed Is Complete
A properly bled system gives a firm, repeatable lever. Pull the lever several times and hold it at the bar. It should stay firm, and the engagement point should be the same on every pull. Sit on the bike, start it, and test the clutch at low speed by pulling in and releasing gradually. Clean, progressive engagement without a wandering bite confirms that the bleed worked. If the lever is still soft, air is likely still present, and the process should be repeated.
Checking for Leaks
Inspect the master cylinder body, the reservoir seal, the slave cylinder, and every line fitting after bleeding. Look for wet spots, fluid beads, or residue along the hose and at crimped fittings. Wipe each area dry with a clean rag, then squeeze the lever and watch closely for seepage. A leak at the fittings often shows up only under pressure, so do not skip this check. Address any leak before riding.
Self-Adjusting Behavior and What to Expect
Hydraulic clutches are self-adjusting, which means that once the system is full of clean fluid and free of air, the engagement point should remain consistent as the clutch pack wears. You do not need to make routine adjustments to maintain lever feel. If the lever is still inconsistent after a thorough bleed and leak check, the problem may lie elsewhere in the system, and that is worth investigating before assuming the clutch itself is at fault. Regular fluid refreshes, especially after heavy use in tight enduro terrain or repeated hard motocross starts, will keep the lever feeling sharp and predictable on the 2013 520 RS SM.
Related Shopping Categories
Shop Cables for a 2013 Beta 520 RS SM Dirt Bike.
Shop Levers for a 2013 Beta 520 RS SM Dirt Bike.
Shop Brake Bleeders for a 2013 Beta 520 RS SM Dirt Bike.
Shop Clutch Kits for a 2013 Beta 520 RS SM Dirt Bike.
Shop Tools for a 2013 Beta 520 RS SM Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.