How to Fix a Spongy or Stiff Clutch on a 1987 Kawasaki KX60 Dirt Bike

Shop parts for a 1987 Kawasaki KX60 Dirt Bike.

What a Stiff or Vague Clutch Lever Feels Like

On a 1987 KX60, the clutch lever should pull with a smooth, consistent motion from the moment your fingers close on it until the plates release. A stiff lever feels heavy from the start, sometimes binding or catching partway through the pull. A notchy lever feels like it snags or ratchets as you squeeze. A soft or vague lever gives you very little feedback, with the bite point drifting around from ride to ride. Each of these traits matters on a two-stroke youth motocross bike, because the clutch controls every launch off the gate, every corner exit, and every moment you need to modulate power on a slick or rutted track.

Why the Cable Is the First Place to Look

The KX60 uses a cable-operated clutch, so the cable running from the lever at the handlebar down to the engine side cover is the main suspect for lever feel. A dry, dirty, or corroded cable creates friction inside its housing, which shows up as a heavy or grabby pull. A cable that has frayed strands at either end can snag inside the housing, and a cable that has been bent sharply where it routes around the frame will drag every time you squeeze. Dry lever pivots add to the problem, since the lever itself can bind before the cable ever moves. Because the KX60 spends much of its life in sand, mud, and dust, grit tends to work its way into all of these points faster than you might expect.

Step-by-Step Cable and Lever Service

  1. Start with the lever. Pull it slowly through its full travel with the bike on a stand and the engine off. Note any spots where it sticks, catches, or feels rough. Also check that the lever returns smoothly to its resting position when released.
  2. Inspect the cable at the handlebar end. Slide the rubber boot back and look for frayed strands, flattened sections, or rust near the lever nipple. Pay attention to the point where the cable enters the housing, since that is where wear often starts.
  3. Inspect the cable at the engine end. Find where the cable exits the housing near the clutch side of the engine. Check the same things you looked for at the lever, and watch for any sign of the cable pulling loose from its seat.
  4. Trace the full routing from lever to engine. Follow the path along the handlebar, down the front of the frame, and back to the engine. Look for kinks, tight bends, or spots where the housing rubs against the frame, a fender bracket, or the throttle cable. Reroute or secure the housing so it sweeps in smooth, wide curves, and never let it pinch when you turn the bars lock to lock.
  5. Lubricate the lever pivot. Remove the pivot bolt, clean the old grime from the lever and the perch, and apply a thin coat of cable-friendly lubricant to the pivot surface before reinstalling. Work the lever several times to spread the lubricant and confirm the motion is smoother.
  6. Disconnect the cable at the engine end and at the lever if you intend to service it. Slide the cable out of the housing, wipe away dirt, and apply lubricant to the bare cable. Work it back and forth as you pour lubricant along the length. Then reinstall it and test the lever again.
  7. Replace the cable if it is frayed, kinked, or still stiff after lubrication. A new cable is inexpensive compared with the time spent fighting a binding one, and it restores a crisp pull that lubrication alone cannot always deliver.

When the Lever Feels Soft or Vague

If the lever feels soft, loose, or inconsistent instead of heavy, the cause is usually different. A stretched cable or excessive freeplay makes the lever travel a long distance before the clutch begins to engage, which can leave you guessing where the bite point lives. Freeplay is set separately during clutch adjustment, so this article does not walk through that process. What you can do at the garage level is confirm that the cable is not stretched, that its ends are seated correctly, and that the routing is not allowing slack to build up. A cable that has been replaced recently, or one that has been sitting under tension in a worn housing, may need the adjustment step before the lever feels right.

Keeping the Lever Feeling Right Through the Season

Because the 1987 KX60 is a small two-stroke, its clutch sees hard use in short, intense bursts, especially during motocross starts and tight corner exits. Make a habit of wiping the cable and lever after each ride where the bike has been in sand or mud. Check the cable ends and routing every few weekends, and keep an eye on the lever pivot since it collects grit quickly. Taking a few minutes to maintain these points keeps the clutch predictable, makes launches more consistent, and gives you the control you need to ride confidently on any track or trail.

Related Shopping Categories

Shop Cables for a 1987 Kawasaki KX60 Dirt Bike.

Shop Levers for a 1987 Kawasaki KX60 Dirt Bike.

Shop Brake Bleeders for a 1987 Kawasaki KX60 Dirt Bike.

Shop Clutch Kits for a 1987 Kawasaki KX60 Dirt Bike.

Shop Tools for a 1987 Kawasaki KX60 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your dirt bike's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.