How to Change the Oil in a 2024 Yamaha TTR50
Shop parts for a 2024 Yamaha TTR50 Dirt Bike.
Proper oil maintenance is essential for the longevity and reliability of your 2024 Yamaha TTR50 dirt bike. Below, MotoSport.com provides a comprehensive, proprietary step-by-step guide to changing the oil on this specific model, including necessary tools, product recommendations, and key owner call-outs to ensure your Yamaha TTR50 runs optimally for years to come.
Tools and Materials Needed
- 10W-40 motorcycle oil (Yamalube or equivalent, 800ml capacity for the TTR50)
- 17mm socket and ratchet or suitable wrench
- Oil drain pan/tray
- Funnel for easy pouring
- Clean rags or paper towels
- Gloves (optional, but helps keep hands clean)
Step-by-Step Guide
-
Warm up your engine
Start the TTR50 and let it idle for a few minutes. Warming up the oil helps it flow more freely, ensuring more contaminants are removed when you drain it. Turn the engine off before proceeding.
-
Set the bike upright and position the oil pan
With the bike on level ground and held upright (not on its side stand), place the oil drain pan directly beneath the drain bolt at the bottom of the engine. This positioning avoids spills and ensures complete drainage. Keeping the bike vertical matters for accuracy and proper drainage.
-
Remove the drain bolt
Using your 17mm socket (or wrench), carefully loosen the drain bolt. Be ready for oil to flow immediately. Remove the bolt by hand, ensuring it does not fall into the pan. Let all the old oil drain completely–this might take a few minutes. Inspect the bolt and the sealing washer for wear or damage and replace if necessary.
-
Reinstall the drain bolt
Once the oil has finished draining, wipe the area around the drain hole. Reinstall the drain bolt and snug it up with your socket or wrench. Do not overtighten–just a firm hand-tighten is sufficient. Overtightening can strip threads or crack the case.
-
Add fresh oil
Remove the oil filler cap/dipstick. Insert a clean funnel into the filler hole and slowly add up to 800ml of the recommended 10W-40 oil (–start with 750ml– to avoid overfilling). Go slow and check the oil level as you near capacity.
-
Check oil level with the dipstick
After adding oil, insert the dipstick back into the filler (do not screw in for this check), then remove it to check the level. The oil should be between the minimum and maximum marks on the dipstick. If it's below the mark, add small amounts and recheck. If you overfill, carefully loosen the drain bolt just enough to let a little oil out, then tighten again.
-
Finalize and clean up
Once the oil is at the correct level, reinstall and tighten the filler cap/dipstick. Start the engine and let it idle for a minute or two, then shut it off and let the oil settle. Double-check the level and top off if necessary. Dispose of old oil responsibly at your local recycling center or auto parts store.
Model-Specific Call-Outs: 2024 Yamaha TTR50
- Oil Capacity: 800ml (always check the side of the case and your owner's manual for confirmation–overfilling can force oil into the airbox and cause poor running conditions).
- Dipstick Use: Always check oil with the TTR50 upright and the dipstick resting in the threads–do not screw it in for an accurate reading.
- Drain Bolt Location: The 17mm drain bolt is on the lower side of the crankcase–access is easier with the kickstand up.
- Oil Change Interval: Every 10–15 operating hours or every 3–4 months for bikes in occasional use. Change more often if riding in excessively dirty or wet conditions.
- Oil Type: Use only motorcycle-specific 10W-40 oil; avoid automotive oils since they may contain friction modifiers incompatible with motorcycle wet clutches.
Tips from MotoSport.com
- Always clean around the filler and drain areas before opening to prevent debris from entering the engine.
- Keep a record of each oil change for warranty and service purposes.
- Allow oil to drain fully before reinstalling the drain bolt for best results.
- Dispose of used oil responsibly—never pour down drains or onto the ground.
- If the oil appears excessively contaminated between intervals, investigate possible causes such as excessive wear or air filter leaks.
Conclusion
Changing the oil on your 2024 Yamaha TTR50 is a straightforward but crucial maintenance task. With a few basic tools, fresh oil, and this MotoSport.com step-by-step guide, you can ensure your dirt bike stays in peak running order for every ride. Refer to your owner's manual for detailed capacity and interval information, and enjoy the confidence that comes from a well-maintained machine.
Related Shopping Categories
Shop Motor Oil for a 2024 Yamaha TTR50 Dirt Bike.
Shop Oil Filters for a 2024 Yamaha TTR50 Dirt Bike.
Shop Oil Drain Pans for a 2024 Yamaha TTR50 Dirt Bike.
Shop Tools for a 2024 Yamaha TTR50 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2024 Yamaha TTR50 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.