How to Change the Oil in a 2024 Sherco 500 SEF FACTORY

Shop parts for a 2024 Sherco 500 SEF FACTORY Dirt Bike.

Maintaining your 2024 Sherco 500 SEF FACTORY means regular oil changes to ensure smooth performance and engine longevity. Below you'll find a proprietary MotoSport.com guide, including needed tools, step-by-step instructions, and model-specific call-outs to make the job seamless for your specific bike.

Tools and Supplies Needed

  • 17mm socket (for oil drain bolts)
  • 8mm socket (for removing oil filter cover)
  • 4mm Allen key (for side covers, if necessary)
  • Torque wrench (recommended for reassembly)
  • New oil filter (must be replaced with every oil change)
  • Replacement oil drain plug washers
  • Fresh engine oil (SAE 10W-60, synthetic, 1.1 liters)
  • Parts cleaning solvent or rag
  • Catch pan for used oil
  • Gloves (optional, but recommended)

Preparation

  • Warm up the engine for a few minutes to allow the oil to flow freely.
  • Locate a clean, flat workspace. Lay down an absorbent pad if needed.
  • Gather all necessary tools and replacement parts to streamline the process.

Step-by-Step Oil Change Instructions

  • Step 1: Remove the Skid Plate (If Installed)
    • If your Sherco 500 SEF FACTORY features a skid plate, remove it using an 8mm socket or appropriate tool for better access to drain bolts and oil filter.
  • Step 2: Drain the Engine Oil
    • Place your catch pan under the engine, directly below the drain plugs.
    • Using the 17mm socket, remove the two magnetic engine drain bolts located at the bottom of the engine case. Both bolts must be removed to completely drain the oil.
    • Be sure to replace the crush washers on each drain bolt during reinstallation to prevent leaks.
    • Allow all the oil to fully drain before proceeding.
  • Step 3: Remove and Replace the Oil Filter
    • Locate the oil filter cover (typically secured with an 8mm bolt) on the side of the engine.
    • Remove the cover, taking note of the orientation and placement of the filter and O-ring. Inspect the O-ring for damage; replace if necessary.
    • Install the new oil filter in the correct orientation as shown in the owner's manual. Improper installation can reduce oil flow and risk engine failure.
    • Reinstall the oil filter cover with a new O-ring if needed. Tighten to 15 Nm torque.
  • Step 4: Clean the Magnetic Drain Bolts
    • Inspect and clean any metal shavings from the magnetic ends of the drain bolts. This helps monitor engine wear and keeps contaminants out of your oil.
    • Reinstall the drain bolts using fresh crush washers. Tighten to 15 Nm torque.
  • Step 5: Replace the Pre-Filters
    • The 2024 Sherco 500 SEF FACTORY is equipped with pre-filters that require cleaning or replacement at every oil change. Remove, check, and either clean or replace them; reinstall with new O-rings if needed.
    • This is critical for engine longevity.
  • Step 6: Fill with New Engine Oil
    • Open the oil fill cap. Use a clean funnel to pour in 1.1L of fresh SAE 10W-60 synthetic engine oil. Double-check oil type and volume as listed in your manual.
    • Check the oil level using the sight glass or dipstick. Add oil in small increments if needed–do not overfill.
    • Tighten the oil fill cap. Double-check all bolts and caps for tightness and leaks.
  • Step 7: Final Checks
    • Start the motorcycle and let it idle for 1–2 minutes. Shut off and allow the oil to settle.
    • Verify the oil level again and inspect under the bike for leaks from the drain plugs, oil filter cover, and pre-filter ports.
    • Reinstall skid plate if removed.
    • Dispose of old oil, filter, and O-rings properly at a recycling center.

Model-Specific Callouts for the 2024 Sherco 500 SEF FACTORY

  • Dual Drain Bolts: Unlike many bikes, both must be removed for a complete drain. Always use new crush washers on both to avoid leaks.
  • Pre-Filters and Magnetic Drain Bolt: Clean pre-filters and magnetic plugs with every oil change. Skipping this maintenance can lead to premature engine wear.
  • Oil Capacity: The correct fill is 1.1L of SAE 10W-60. Overfilling or underfilling can damage the engine.
  • Filter Orientation: Installing the oil filter backwards blocks oil flow. Reference your owner's manual or take note of the position before removing the old filter.
  • Torque Values: All drain and filter cover bolts should be tightened to 15 Nm.
  • Change Interval: Sherco recommends changing oil and filter each time—do not reuse filters for this high-performance enduro engine.

Conclusion

Changing the oil in your 2024 Sherco 500 SEF FACTORY is a straightforward task when following these steps and using quality replacement parts from MotoSport.com. Always reference your owner's manual for the latest specifications and disposal recommendations. Frequent maintenance keeps your Sherco ready for every adventure, race, or trail.

If in doubt or lacking tools, consult a MotoSport.com certified technician for assistance.

Related Shopping Categories

Shop Motor Oil for a 2024 Sherco 500 SEF FACTORY Dirt Bike.

Shop Oil Filters for a 2024 Sherco 500 SEF FACTORY Dirt Bike.

Shop Oil Drain Pans for a 2024 Sherco 500 SEF FACTORY Dirt Bike.

Shop Tools for a 2024 Sherco 500 SEF FACTORY Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Sherco 500 SEF FACTORY Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.