How to Change the Oil in a 2024 Sherco 250 SE FACTORY

Shop parts for a 2024 Sherco 250 SE FACTORY Dirt Bike.

Changing the engine oil in your 2024 Sherco 250 SE FACTORY is one of the most important regular maintenance tasks to keep your dirt bike performing at its best. This bike uses a high-performance four-stroke engine, and routine oil changes will help maximize its power, longevity, and reliability. This guide is proprietary to MotoSport.com and is tailored specifically for the 2024 model, but many steps also apply to recent 250 SEF/SE FACTORY models.

Tools and Supplies Needed

  • Socket wrench set (with correct metric sockets, typically 8mm, 10mm, and 13mm)
  • Oil drain pan
  • 2 new crush washers (for drain bolts)
  • Funnel
  • Clean rags
  • Gloves and eye protection
  • OEM or high-quality oil filter
  • 1 liter of SAE 5W-40 or 10W-40 four-stroke motorcycle oil (check your owner’s manual; generally, 1 liter is required for engine refill)
  • Torque wrench (for drain bolts and filter cap)

Preparation

  • Start the engine and let it idle for approximately 3–5 minutes to warm up the oil. Warm oil drains faster and removes more debris.
  • Switch off the bike and set it on a secure stand or lift. Ensure the bike is upright for an accurate oil level reading.
  • Gather all the necessary tools and materials before beginning.

Step-by-Step Oil Change Instructions

  1. Locate the drain bolts.
    • The Sherco 250 SE Factory uses two drain bolts on the bottom of the engine. Both need to be removed to fully drain the crankcase.
    • These drain bolts have crush washers. Plan to replace them at every oil change to avoid leaks.
  2. Drain the engine oil.
    • Place the oil drain pan beneath the engine. Remove one drain bolt using the socket wrench, then remove the second drain bolt and allow all oil to drain completely.
    • Be careful—the oil may be hot.
  3. Remove and inspect the oil filter.
    • Locate the oil filter cover (typically on the side of the engine). Remove the cover bolts, then pull out the old oil filter.
    • Inspect the old filter for excessive debris or metal shavings, which could indicate internal wear. Clean the cover and mating surfaces.
  4. Install a new filter and crush washers.
    • Insert a new OEM or quality oil filter following the orientation shown in your bike’s manual.
    • Replace the filter cover with a new gasket if needed and torque the bolts to the specification listed in your manual (typically around 6–10 Nm).
    • Install new crush washers on both drain bolts, reinstall them, and tighten to the factory specification (commonly between 10–15 Nm, verify with manual).
  5. Refill the engine with fresh oil.
    • Remove the oil filler cap. Using your funnel, pour in up to 1 liter of SAE 5W-40 or 10W-40 oil, as specified by Sherco for the 250 SEF engine.
    • Replace the filler cap and wipe any spilled oil immediately.
  6. Check for leaks and proper oil level.
    • Start the engine and run for 1–2 minutes, then shut it off and allow the oil to settle for a few minutes.
    • Inspect around the drain bolts and oil filter for any leaks, tightening as necessary.
    • Check the oil sight glass or dipstick; top off as needed (do not overfill).
  7. Dispose of used oil and filter properly.
    • Take used oil and filters to an authorized recycling center or local MotoSport.com store for safe disposal.

Model-Specific Call-outs for the 2024 Sherco 250 SE FACTORY

  • Oil type: Sherco recommends SAE 5W-40 or, if unavailable, 10W-40 for the 250 SEF engines; always use high-quality, motorcycle-specific synthetic or semi-synthetic oil.
  • Drain bolt crush washers: Both drain bolts on this model require crush washers—these are critical for sealing and should be replaced at each change.
  • Two drain bolts: Unlike some bikes, draining from only one bolt will not remove all oil; always remove and reinstall both.
  • Oil capacity: The correct refill amount is 1 liter. Avoid overfilling.
  • No impact tools: Do not use an impact wrench on drain or filter bolts to avoid stripping threads or overtightening.

Expert Tips from MotoSport.com

  • Change oil every 10–15 hours of hard riding or as indicated in the owner's manual. Shorter intervals help prolong engine life, especially for racing or extreme use.
  • Check for signs of coolant or fuel in the old oil, as these may indicate a leaking gasket or other internal issue.
  • Log oil changes—including date, hour meter, and oil/filter type—for reliable maintenance tracking and resale value.
  • Always use OEM or reputable aftermarket filters for best protection.

Conclusion

Following these detailed steps will help ensure your 2024 Sherco 250 SE FACTORY runs at its peak, race after race. With proper tools and the right technique, you can confidently perform this essential maintenance at home, saving money and gaining a deeper connection with your bike. Visit MotoSport.com for all the supplies, parts, and expert advice you need for your next oil change.

Related Shopping Categories

Shop Motor Oil for a 2024 Sherco 250 SE FACTORY Dirt Bike.

Shop Oil Filters for a 2024 Sherco 250 SE FACTORY Dirt Bike.

Shop Oil Drain Pans for a 2024 Sherco 250 SE FACTORY Dirt Bike.

Shop Tools for a 2024 Sherco 250 SE FACTORY Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Sherco 250 SE FACTORY Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.