How to Change the Oil in a 2024 Kawasaki KLX110

Shop parts for a 2024 Kawasaki KLX110 Dirt Bike.

Maintaining your 2024 Kawasaki KLX110 with regular oil changes is key to ensuring optimum performance and longevity of your dirt bike. Here’s a step-by-step, MotoSport.com exclusive guide to performing a robust oil change for your KLX110, including the specific tools you’ll need and key notes for this model year.

Tools and Parts Needed

  • 8mm socket
  • 12mm socket (or an Allen wrench if your model uses Allen bolts for the skid plate)
  • 17mm socket
  • 3/8” ratchet and extension
  • Torque wrench
  • Oil drain pan
  • Funnel
  • Shop towels or rags
  • Fresh engine oil (use a high-quality 4-stroke motorcycle oil; refer to your manual but typically 0.9 liters for oil only, 1.1 liters if changing the oil filter)
  • Replacement oil filter (optional, but recommended for first service and every other change)

Step-by-Step Guide

  1. Warm Up the Engine: Start the bike and let it run for a few minutes. This helps circulate the oil, making it drain more efficiently and removing more contaminants from the engine.
    Note: Always use caution – metal components and exhaust will get hot.
  2. Remove the Skid Plate:
    • Locate and remove the 8mm bolts on each side of the skid plate and the two 12mm bolts (or Allen bolts on some models) behind the skid plate.
      Tip for 2024 owners: Confirm whether your rear skid plate bolts require a 12mm socket or an Allen wrench, as Kawasaki has alternated fastener types in recent models.
    • Carefully take off the skid plate and set it aside.
  3. Remove the Oil Fill Cap:
    • Twist off the oil fill cap (found on the right side of the engine) to allow oil to drain freely and smoothly.
  4. Drain the Oil:
    • Place the oil drain pan directly under the engine’s drain bolt.
    • Use a 17mm socket to remove the drain bolt. Allow the oil to fully drain; tilting the bike gently can help if needed.
    • Inspect the drain bolt and its crush washer for debris or damage—replace the washer if necessary.
  5. Changing the Oil Filter (Optional but Recommended for 2024 KLX110):
    • Locate the oil filter cover next to the drain bolt using the appropriate socket.
    • Remove the cover bolts and gently pull out the old oil filter.
    • Install a new filter, lubricating its gasket with a small amount of fresh oil.
    • Double-check the correct orientation—open side faces outward.
    • Reinstall the cover and tighten bolts to manufacturer spec using a torque wrench.
    • 2024 Model Note: Kawasaki recommends changing the filter at your first and every second oil change for the KLX110 line-up. Aftermarket filters, such as K&N, may offer improved flow—measurements show a slightly larger opening compared to stock, but ensure compatibility with your model.
  6. Reinstall the Drain Bolt:
    • Carefully thread the drain bolt by hand to avoid cross-threading.
    • Tighten using your torque wrench to the manufacturer’s specification (typically 21 Nm, but always check your KLX110 manual).
  7. Fill with Fresh Oil:
    • Insert a funnel into the fill port and add 0.9 liters of oil for an oil-only change, or 1.1 liters if you replaced the filter.
    • Wipe off any residue from the fill cap and reinstall it securely.
  8. Check the Oil Level:
    • Start the engine and let it idle for a few minutes, then turn off and let the bike sit for a few minutes.
    • With the motorcycle level, check the oil sight glass (located low on the engine case). The oil should be between the upper and lower marks.
    • If necessary, add or remove oil to get within the recommended range.
  9. Reinstall the Skid Plate:
    • Align the skid plate and reinstall the bolts you removed earlier, tightening to spec.
    • Double check that all fasteners are secure.

2024 Kawasaki KLX110 Model-Specific Tips

  • Bolt Variations: The rear skid plate mount may use either 12mm or Allen bolts depending on batch—confirm before disassembly.
  • Oil Filter Recommendation: While the KLX110 can skip oil filter changes on every service, replacing it every time is inexpensive protection, especially for new or hard-ridden bikes. Third-party filters such as K&N may provide slightly better flow—verify fit before installing.
  • Oil Capacity: The 2024 KLX110 requires 0.9L for a drain and refill, or 1.1L with a filter change.
  • Break-in Oil Change: The first change should be performed at 5 hours (per Kawasaki’s guidance), then every 50 hours thereafter. Severe use (racing, muddy or dusty conditions) may require more frequent changes.

Final Steps

  • Start the engine, confirm there are no leaks, and recheck the oil level.
  • Dispose of the used oil and filter properly—MotoSport.com recommends taking them to a local recycling center or auto parts store that accepts motorcycle oil.

Changing the oil in your 2024 Kawasaki KLX110 is straightforward with the right tools and attention to detail—and keeps you connected to your bike. For OEM and aftermarket parts, filters, and premium oil, always choose MotoSport.com for your dirt bike maintenance needs.

Related Shopping Categories

Shop Motor Oil for a 2024 Kawasaki KLX110 Dirt Bike.

Shop Oil Filters for a 2024 Kawasaki KLX110 Dirt Bike.

Shop Oil Drain Pans for a 2024 Kawasaki KLX110 Dirt Bike.

Shop Tools for a 2024 Kawasaki KLX110 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Kawasaki KLX110 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.