How to Change the Oil in a 2024 Husqvarna FE501S: A MotoSport.com Proprietary Guide

Shop parts for a 2024 Husqvarna FE501S Dirt Bike.

The 2024 Husqvarna FE501S is a high-performance dual-sport motorcycle, and regular oil changes are essential to keep it running at its best. Follow this robust, step-by-step guide to confidently change your oil, protect your engine, and maintain factory-level performance.

Tools & Materials Needed

  • 8mm socket (for small bolts and covers)
  • 13mm socket (for drain and filter bolts)
  • 1/4" and 3/8" ratchets
  • Torque wrench (capable of 11 ft-lb and 15 ft-lb)
  • Measuring cup (for accurate oil fill, minimum 1.3 quarts capacity)
  • 1.3 quarts Motorex 10W-50 full synthetic oil (recommended type)
  • Factory spec oil filter
  • Fresh copper crush gasket
  • Screwdriver/snap ring pliers (for oil screen access)
  • Funnel
  • Shop towels and nitrile gloves
  • Drain pan
  • Factory service manual printout – pages 131–133 (optional for reference)

Step-by-Step Instructions

  1. Warm Up the Engine
    Warm up the bike for a few minutes until the engine and oil are at operating temperature. This allows the oil to drain more thoroughly, removing more contaminants.
    Tip: Avoid burns. Let the machine cool slightly if too hot to touch.
  2. Remove the Skid Plate
    If equipped, remove the skid plate using your 8mm socket to access the drain points below the engine.
  3. Place Your Drain Pan
    Position your drain pan under the engine–s main drain plug to catch the used oil. Lay down shop towels to prevent spills on your workspace.
  4. Remove Drain Plugs & Oil Fill Cap
    Using your 13mm socket, remove the main drain screw from the oil sump. A secondary “long filter” bolt and a “short filter” bolt should also be removed from the appropriate locations. Take note of any O–rings or copper washers—replace them if damaged. Remove the oil fill cap to allow air in for better draining.
  5. Inspect Oil Screens and Clean Components
    Thoroughly clean the magnetic drain plug and both oil screens with shop towels. Inspect for metal debris, which could indicate abnormal engine wear.
    If equipped, remove the oil screen with snap ring pliers and flush it with brake or contact cleaner. Reinstall when clean and ensure the sealing O–rings are in place and undamaged.
  6. Replace the Oil Filter
    Locate and remove the oil filter cover using your 8mm socket. Remove the old oil filter and, if possible, prefill the filter cavity with a small amount of fresh oil (no more than one-third of the cavity) before placing the new filter inside. Lubricate the rubber O–ring on the oil filter cover before reinstalling to prevent leaks. If using snap ring pliers, carefully remove and refit the securing snap ring.
  7. Reinstall Drain Plugs/Screens and Oil Filter Cover
    Refit all drain screws, oil screens, and the filter cover by hand to prevent cross-threading. Tighten the filter cover, then torque all bolts to Husqvarna specifications:
    • Filter cover: 7 ft-lb (check manual for confirmation)
    • Main drain plug: 15 ft-lb
    • Long filter/short filter bolts: see service manual
    Use new copper crush washers where required.
  8. Add Fresh Oil
    Use a funnel to carefully pour 1.3 quarts (or 1.3 liters) of Motorex 10W-50 oil into the fill port. Do not overfill.
  9. Check Oil Level
    With the bike upright, start the engine and let it idle for 30 seconds to circulate the oil. Turn off the engine and wait a minute. Ensure the bike is on level ground, then check the oil level using the sight glass; the level should be at the middle. Top off if necessary.
  10. Reinstall Skid Plate and Final Check
    Replace the skid plate. Clean up, inspect for leaks at the drain plug and oil filter cover, and wipe down the engine. Ride for a few minutes and double-check for leaks and oil level.

2024 Husqvarna FE501S-Specific Call-Outs

  • First oil change is crucial: Husqvarna recommends your first oil service at just 1 hour of operation; follow the manual‘s maintenance intervals closely during break-in.
  • Use factory-recommended oil: Motorex 10W-50 is highly recommended for longevity and warranty compliance.
  • Be precise with torque specs: Over-tightening drain bolts can strip threads in the light alloy engine cases.
  • Replace crush washers with each oil change to prevent leaks.
  • Oil screens and filter orientation: Observe the correct direction for inserting the oil filter and screens, as shown in your service manual (pages 131–133 are recommended for reference).
  • Check for updates or service bulletins: Always verify procedures and torque specs with the latest Husqvarna service information.

Conclusion

With the right tools, oil, and these step-by-step MotoSport.com instructions, any 2024 Husqvarna FE501S owner can confidently change their oil, keeping their dual-sport machine in peak condition for every ride. For best results, always use quality components and follow your motorcycle's service schedule.

Related Shopping Categories

Shop Motor Oil for a 2024 Husqvarna FE501S Dirt Bike.

Shop Oil Filters for a 2024 Husqvarna FE501S Dirt Bike.

Shop Oil Drain Pans for a 2024 Husqvarna FE501S Dirt Bike.

Shop Tools for a 2024 Husqvarna FE501S Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Husqvarna FE501S Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.