How to Change the Oil in a 2024 Honda XR650L

Shop parts for a 2024 Honda XR650L Dirt Bike.

Regular oil changes are essential for maintaining the performance and longevity of your 2024 Honda XR650L. This guide, proprietary to MotoSport.com, covers all the tools needed, step-by-step instructions, and crucial model-specific call-outs for a smooth, mess-free oil change.

Tools & Supplies Needed

  • 8mm, 10mm, 12mm, and 17mm sockets and wrenches – for drain bolt and accessory removal
  • Oil drain pan – to collect old oil
  • Rags or shop towels – to wipe up spills
  • Funnel
  • New oil filter (recommended BMW: Honda OEM filter, part number 15410-KF0-315)
  • Fresh oil: 10W-40 motorcycle oil, 2.6 liters (Honda GN4 recommended)
  • Crush washer for drain bolt (replace if worn)
  • Contact cleaner (optional, for cleaning up)
  • Gloves and safety glasses
  • Magnetic drain bolts (optional, for extra engine protection)

Model-Specific Call-Outs for the 2024 Honda XR650L

  • Warm the engine for a few minutes; this helps the oil drain completely and can carry away more contaminants

    .
  • For XR650L models, oil is stored in both the engine crankcase and frame – so there are two separate drain plugs to remove

    .
  • Honda specifies changing oil and filter every 2,000 miles (3,200 km), or after the first 600 miles (1,000 km) on a new engine

    .
  • The oil filter cover uses 8mm bolts, and the engine and frame drain bolts are 17mm and 12mm, respectively

    .
  • Be sure to clean or inspect the oil screen every 3-4 oil changes or during the break-in, as this crucial filter is often neglected

    .

Step-by-Step Oil Change Guide

  1. Prep the bike and work area:
    Park the XR650L on a firm, level surface and engage the side or center stand. Ensure proper ventilation if working indoors. Warm up the engine for several minutes to get the oil up to operating temperature, then turn the bike off and let it sit for a couple of minutes

    .
  2. Remove engine guards (if installed):
    If your bike has a skid plate or engine crash bar, remove it with the appropriate socket (typically 10mm or 12mm). This gives you full access to both drain bolts

    .
  3. Remove the oil fill dipstick:
    Unscrew the oil dipstick/fill cap on the right side. This prevents a vacuum from forming and helps oil drain freely

    .
  4. Drain oil from the crankcase and frame:
    • Place the drain pan beneath the crankcase drain bolt (under the engine, 17mm).
    • Carefully loosen and remove the bolt. Oil will start draining—watch for hot oil.
    • Next, move the drain pan beneath the frame’s downtube drain bolt (just below the steering head, 12mm).
    • Remove the frame drain bolt. Allow all oil to drain completely. Wait several minutes for the oil to empty out of both locations

      .
  5. Inspect and clean/reinstall:
    • If using magnetic drain bolts, inspect for any excessive metal debris.
    • Check and replace crush washers if damaged.
    • Tighten drain bolts to factory torque specs from your owner’s manual

      .
  6. Change the oil filter:
    • The oil filter is located at the right side of the engine. Remove the filter cover bolts (8mm socket).
    • Carefully pull off the cover; the old filter may stick—use care not to damage the sealing gasket.
    • Replace with a fresh filter. Be sure the open end faces out, and lubricate the filter’s rubber O-ring with a dab of fresh oil before installation.
    • Reinstall the oil filter cover and torque bolts evenly to specification.
  7. Fill with new oil:
    • Insert a funnel into the oil fill port.
    • Pour in 2.6 liters of 10W-40 motorcycle oil

      .
    • Let the oil settle for a minute, then check with the dipstick (insert but do not screw in to check level).
    • Add a small amount more if below the full mark—do not overfill.
  8. Check for leaks and finish up:
    • Start the bike and let it idle for a minute—watch for any oil leaks around the filter cover or drain bolts.
    • Shut off and let the bike sit for a few minutes, then recheck the oil level and top off if needed.
    • Reinstall skid plate/engine guards if removed earlier.
    • Dispose of used oil and filter responsibly—do not pour down a drain or on the ground

      .

Final Model-Specific Notes for the 2024 XR650L

  • Ensure both frame and crankcase are thoroughly drained each change.
  • Crush washers are small yet vital for a leak-free seal—replace at each change if worn

    .
  • Inspect/clean the oil screen at least every 3-4 oil changes, as recommended for XR650L engines

    .
  • Always use the proper oil viscosity (10W-40) and volume (2.6 liters) for the 2024 XR650L, as using less can endanger the engine

    .
  • If uncertain about torque specs, refer to your Honda owner’s manual for the 2024 XR650L or ask a certified mechanic

    .

Changing the oil on your 2024 Honda XR650L is a straightforward task that pays off greatly in engine life and reliability. For quality OEM parts, trusted oil brands, and magnetic drain bolts, visit MotoSport.com—everything you need for your next maintenance day, all in one place.

Related Shopping Categories

Shop Motor Oil for a 2024 Honda XR650L Dirt Bike.

Shop Oil Filters for a 2024 Honda XR650L Dirt Bike.

Shop Oil Drain Pans for a 2024 Honda XR650L Dirt Bike.

Shop Tools for a 2024 Honda XR650L Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2024 Honda XR650L Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.