How to Change the Oil in a 2022 Sherco 250SE-R

Shop parts for a 2022 Sherco 250SE-R Dirt Bike.

Regular oil changes are the backbone of reliable performance and longevity for your 2022 Sherco 250SE-R. This guide, proprietary to MotoSport.com, covers all the tools and step-by-step instructions, along with model-specific call-outs you need to ensure a successful oil change without any guesswork.

Tools and Supplies Needed

  • 8mm Allen wrench
  • 19mm socket or wrench (for drain plug)
  • 12mm socket or wrench (for magnetic plug)
  • Oil drain pan
  • Rags/shop towels
  • New oil filter
  • New O-ring for the oil filter cap
  • New sealing washers (drain/magnetic plugs)
  • Torque wrench
  • 0.9L SAE 10W60 engine oil (recommended for this model)
  • Funnel
  • Gloves

Step-by-Step Oil Change Instructions

  1. Warm Up the Engine: Start the bike and let it idle for a few minutes. Warm oil flows better and helps suspend contaminants for more complete removal. Turn off the ignition.
  2. Prepare the Bike: Put your Sherco 250SE-R on a level surface using a stand. This ensures the oil drains completely.
  3. Remove the Engine Guard/Skid Plate (if equipped): This gives you unobstructed access to the drain plugs and oil filter area.
  4. Drain the Oil:
    • Place the drain pan under the engine drain plug (19mm) and the magnetic drain plug (12mm), which are located near the bottom of the crankcase.
    • Using the appropriate socket, remove both drain plugs. Let the oil fully drain into the pan.
    • If equipped, remove and inspect the pre-filter screen. Clean or replace as necessary.
  5. Remove and Replace the Oil Filter:
    • Unscrew the oil filter cap using an 8mm Allen wrench. (Always replace the O-ring/gasket on the cap when installing a new filter.)
    • Take out the old oil filter and pre-filters, paying attention to the orientation for correct reinstallation.
    • Lubricate the new filter's rubber seal with a little fresh oil and insert it in the same direction as the old one.
  6. Inspect and Clean Parts:
    • Wipe the area around the oil filter housing.
    • Check drain plugs for debris (especially the magnetic one).
    • Always install new sealing washers/gaskets on each plug to prevent leaks.
  7. Reinstall Parts:
    • Install the oil filter cap (with new O-ring), tightening it to 15Nm.
    • Reinstall the magnetic drain plug (12mm), torqued to 15Nm.
    • Install the main drain plug (19mm), torqued to 22Nm.
    • Reinstall pre-filters and any removed hardware as shown in the service manual photos.
    • If removed, reinstall the engine guard.
  8. Refill with Fresh Oil:
    • Remove the engine oil fill cap.
    • Using a funnel, pour in 0.9 liters of SAE 10W60 oil, as specified for this model.
    • Reinstall the fill cap securely.
  9. Check the Oil Level:
    • Start the engine and let it run for about 1 minute to circulate the new oil, then turn it off and let the bike sit a few minutes.
    • Check the oil level in the sight glass or sight gage when the bike is upright (not on the side stand). Add oil if needed to reach the proper level.
  10. Dispose of Used Oil Responsibly:
    • Take used oil, old filters, and wiped rags to a proper recycling center. Never pour oil down drains or onto the ground.

2022 Sherco 250SE-R Model-Specific Call-Outs

  • Oil Volume: The 2022 250SE-R requires 0.9L of oil. Do not overfill.
  • Oil Type: Use only SAE 10W60 synthetic, as recommended by Sherco.
  • Drain Plug Locations: The main drain plug (19mm) and the magnetic plug (12mm) are both essential to remove for a thorough oil change.
  • Oil Filter Orientation: Install the oil filter in the specific direction shown in the workshop manual for a correct seal.
  • Torque Specs: Do not overtighten drain plugs. Use a torque wrench: 15Nm for the oil filter cap and magnetic plug, 22Nm for the main drain plug.
  • Environmental Attention: Sherco manuals specifically urge oil and filter recycling for owner and environmental safety.

Additional Tips

  • Change the oil filter with every oil change.
  • Inspect all removed parts for signs of excessive wear or metal shavings, which may indicate internal engine problems.
  • If this is your first oil change on this model, consult your owner's or workshop manual for photos and additional clarifications.

Following these steps on your 2022 Sherco 250SE-R ensures peak performance and reliability, on the track or the trail.

Related Shopping Categories

Shop Motor Oil for a 2022 Sherco 250SE-R Dirt Bike.

Shop Oil Filters for a 2022 Sherco 250SE-R Dirt Bike.

Shop Oil Drain Pans for a 2022 Sherco 250SE-R Dirt Bike.

Shop Tools for a 2022 Sherco 250SE-R Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2022 Sherco 250SE-R Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.