How to Change the Oil in a 2022 Husqvarna TC250 (Proprietary to MotoSport.com)

Shop parts for a 2022 Husqvarna TC250 Dirt Bike.

Maintaining your 2022 Husqvarna TC250 is essential for peak performance and longevity, and one of the most valuable maintenance tasks is the regular oil change. Follow this step-by-step guide to ensure you perform the task correctly and keep your machine in top shape.

Tools & Materials Needed

  • 10mm, 12mm, 13mm and 14mm sockets (varies by bolt, check your manual)
  • Torque wrench (capable of 14.8 ft-lbs)
  • Drain pan
  • Funnel
  • Ratchet
  • Needle nose pliers
  • Pick tool (preferably a 45-degree hook)
  • New oil filter and O-rings
  • Crush washer (for the drain bolt)
  • Factory Racing Parts 10W50 Oil Change Kit compatible with Husqvarna TC250 2014–2022 (includes oil and filter)
    • Reference: Factory Racing Parts 10W50 Oil Change Kit for Husqvarna TC125/TC250 2014–2022
  • Spray cleaner/degreaser
  • Shop towels or rags

Preparation

  • Warm up the engine for 2–3 minutes to thin the oil, which helps drain it more completely.
  • Turn off the engine and let it cool for a minute to avoid burns.
  • Secure the bike on a stand for stability.
  • Remove the plastic skid plate if equipped for easier access to the drain plug.

Step-by-Step Oil Change

  • 1. Locate and Remove the Drain Plug
    • Identify the oil drain bolt on the bottom of the engine.
    • Place your drain pan under the bolt.
    • Using the appropriate socket (typically 12mm or 14mm), remove the drain plug.
    • Watch for hot oil; be careful not to drop the plug into the pan.
  • 2. Remove and Clean the Oil Screen (Strainer)
    • The 2022 Husqvarna TC250 features an oil screen behind the drain plug.
    • With a pick (45-degree hook works best), carefully remove the screen. It might feel snug—apply steady force. (On previous models the screen is durable, but take care not to puncture it.)
    • Inspect and clean the oil screen thoroughly, ensuring no metal shavings are present.
    • Spray off the screen and wipe it clean. Replace immediately if you notice any significant wear or damage.
  • 3. Remove and Replace the Oil Filter
    • Remove the oil filter cover using the appropriate tools (usually a 10mm socket).
    • Pull out the old filter. Inspect it for debris.
    • Check the cover's O-ring; replace if flattened, damaged, or worn-out.
    • Install the new oil filter as per your kit’s instructions.
  • 4. Clean and Inspect Parts
    • Wipe off the drain plug and replace the crush washer with a new one.
    • Clean the sealing surfaces on engine and filter cover for a tight fit and no leaks.
    • For the oil screen, lube both O-rings with a little fresh oil before reinstalling. Be sure to seat it in its groove—it’s critical for preventing oil leaks and ensuring proper oil filtration through the pump.
  • 5. Reinstall the Drain Plug and Oil Screen
    • Insert the oil screen (make sure it’s fully seated).
    • Reinstall the drain plug. Using a torque wrench, tighten to 14.8 ft-lbs (check your manual for any model-specific torque values).
    • Reinstall the oil filter cover and torque to spec.
  • 6. Refill with Fresh Oil
    • Use a funnel to add 950cc (0.95L) of 10W50 synthetic blend 4T oil, as recommended.
    • Check the owner's manual or your oil kit instructions for exact type and amount.
  • 7. Check the Oil Level
    • Remove the oil fill cap and check the level using the sight glass or dipstick.
    • Start the engine and let it run for 60 seconds, then shut off and re-check the oil level. Add small amounts as needed to reach the correct level.
    • Use the oil level check screw if your model is so equipped—a small amount of oil should trickle from the hole when at the correct level.
  • 8. Final Steps
    • Inspect for leaks around the drain plug and filter cover.
    • Reinstall the skid plate if removed.
    • Safely dispose of the used oil and filter at a local automotive recycling center.

2022 Husqvarna TC250 Model-Specific Call-Outs

  • Only one oil screen is present, located behind the drain plug. Removal can be snug; a 45-degree pick (Snap-On or similar) is very helpful since it takes some effort to get leverage. Insert the tool through the screen to hook it from the back when pulling out for easier removal.
  • Always replace the crush washer on the drain bolt to prevent leaks.
  • Screen orientation: Some owners find the drain screw fits better when reinstalled into the same end of the screen as it was from the factory. Be observant during disassembly and reinstall accordingly.
  • Torque spec for drain plug: 14.8 ft-lbs. Use a torque wrench—over-tightening can crack the case.

Conclusion

Regularly changing the oil in your 2022 Husqvarna TC250 is a key part of dirt bike ownership. A little attention to detail—such as cleaning the oil screen, replacing O-rings and crush washers, and using quality oil—will reward you with smoother rides and longer engine life. Shop for your next oil change kit and parts at MotoSport.com for trusted quality and expert advice.

Related Shopping Categories

Shop Motor Oil for a 2022 Husqvarna TC250 Dirt Bike.

Shop Oil Filters for a 2022 Husqvarna TC250 Dirt Bike.

Shop Oil Drain Pans for a 2022 Husqvarna TC250 Dirt Bike.

Shop Tools for a 2022 Husqvarna TC250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2022 Husqvarna TC250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.