How to Change the Oil in a 2022 Husqvarna FE350HQ: A Step-by-Step Guide
Shop parts for a 2022 Husqvarna FE350HQ Dirt Bike.
This MotoSport.com exclusive how-to guide walks 2022 Husqvarna FE350HQ owners through a complete oil change, covering all the essential tools, every step, and key model-specific details you need to keep your bike running strong.
Tools and Materials Needed
- 13mm socket or box wrench (for drain plug)
- 8mm socket or T30 Torx bit (for skid plate removal)
- Oil drain tray/pan
- New oil filter (Husqvarna recommended)
- New copper washer for drain plug
- Brake cleaner or kerosene (optional, for cleaning screens)
- Clean rags or shop towels
- Torque wrench (recommended, for correct tightening)
- Engine oil (full synthetic 4-stroke oil, check owner's manual for spec)
- Oil funnel
- Rubber gloves (optional, keeps hands clean)
- Stand or hoist (to steady bike)
Special Call-outs for 2022 Husqvarna FE350HQ Owners
- The FE350HQ features a magnetic sump plug, oil screen, and an oil filter.
- There are several Allen-head plugs under the engine– do not remove these unless you've confirmed their function—mistakenly removing the oil pump cover or wrong plugs can cause major issues.
- Always replace the copper washer on the drain plug to prevent leaks.
- Do not over-tighten the sump plug; this can strip threads in the soft aluminum engine case.
- Never reuse O-rings or washers if damaged—always inspect and replace as necessary.
Oil Change Procedure for 2022 Husqvarna FE350HQ
-
Prep & Safety
- Warm up the engine for a few minutes to allow the oil to drain more easily.
- Turn off the engine and steady your bike on a hoist, center stand, or bike lift. If you're using the sidestand, ask someone to help stabilize the bike while working below it.
-
Remove Skid/Bash Plate
- Locate the two bolts (use an 8mm socket or T30 Torx bit). Remove them and slide the plate clear of the frame for unimpeded access to the underside of the engine.
- Set the skid plate aside for cleaning while you work.
-
Position Oil Drain Pan
- Place your oil drain pan directly below the rear/lowest point of the engine, where the drain plug is located.
-
Remove Magnetic Drain Plug
- Find the 13mm hex head bolt (magnetic drain plug with copper washer) at the rear of the engine; do not remove any similar-looking Allen bolts nearby.
- Carefully loosen and remove the plug, allowing oil to drain completely into the pan.
- Inspect the magnetic tip for any metal shavings — a small amount is normal, but large shards may indicate internal wear.
-
Remove and Clean Oil Screen
- Locate the oil screen (consult owner's manual if unsure; usually accessible with a small wrench).
- Gently remove and inspect/clean the screen using brake cleaner or kerosene and a stiff brush, such as an old toothbrush.
-
Replace the Oil Filter
- Locate the oil filter cover; remove the bolts and set aside.
- Pull out the old oil filter, noting its orientation. Replace with a new, compatible filter.
- Lubricate new O-rings with fresh oil before installing—do not reuse worn O-rings.
- Reinstall the filter cover securely.
-
Reinstall Oil Screen & Drain Plug
- Once oil is fully drained, reinstall the cleaned oil screen and secure it.
- Install a new copper washer on the 13mm sump plug and thread it in by hand before snugging gently with your socket.
- If using a torque wrench, tighten according to Husqvarna's spec (commonly about 15 Nm, but check your owner's manual).
- Do not over-tighten—the copper washer provides the seal.
-
Refill with Oil
- Remove the oil fill cap (usually on top/right side of engine).
- Using a funnel, pour in the recommended volume/type of oil (generally about 1.1 liters for the FE350, but check your manual for exact spec).
- Pause midway and wait a minute for oil to settle to avoid overfilling.
- Reinstall oil fill cap after filling.
-
Run Engine and Check for Leaks
- Start the engine and let idle for a minute, then switch off.
- Inspect the drain plug, oil screen, and filter area for any leaks.
- After settling, use the dipstick or inspection window to check oil level; top off if necessary.
-
Reinstall Skid Plate
- Clean the skid plate if needed, then bolt it back into place.
-
Dispose of Used Oil Responsibly
- Pour used oil into a sealed container and deliver it to a local recycling center or auto parts store; never dump oil in drains or on the ground.
2022 Husqvarna FE350HQ Oil Change Model-Specific Reminders
- Be cautious: only remove the properly identified magnetic drain plug and oil screen–other Allen-head bolts under the engine are not for oil draining and can cause problems if removed (such as unintended access to internal engine parts).
- Always use a new copper washer with the drain plug for a proper seal each time.
- Replace the oil filter every oil change for maximum engine protection and longevity.
- Consult your service manual for torque settings and oil specifications.
Changing your oil regularly on the Husqvarna FE350HQ ensures smooth, reliable performance and a long engine life. Always ride safe and service your bike with confidence, powered by MotoSport.com.
Related Shopping Categories
Shop Motor Oil for a 2022 Husqvarna FE350HQ Dirt Bike.
Shop Oil Filters for a 2022 Husqvarna FE350HQ Dirt Bike.
Shop Oil Drain Pans for a 2022 Husqvarna FE350HQ Dirt Bike.
Shop Tools for a 2022 Husqvarna FE350HQ Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2022 Husqvarna FE350HQ Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.