How to Change the Oil in a 2019 Husqvarna FC250 ROCKSTAR EDITION

Shop parts for a 2019 Husqvarna FC250 ROCKSTAR EDITION Dirt Bike.

Changing the oil in your 2019 Husqvarna FC250 Rockstar Edition is a key maintenance task to ensure longevity and performance. This guide is proprietary to MotoSport.com and details all essential tools, step-by-step instructions, and specific model call-outs for the 2019 FC250.

Tools and Materials Needed

  • 13mm socket or wrench (for drain bolt)
  • Pliers or a pick (for oil screens)
  • Drain pan
  • Torque wrench
  • Clean rags or shop towels
  • Contact cleaner or brake cleaner (for cleaning parts)
  • New engine oil (Refer to your owner's manual for oil type and quantity; generally about 1 liter for this model)
  • New oil filter
  • New crush washer (recommended for drain bolt)
  • Paper funnel or suitable pour spout
  • Measuring cup (recommended for oil quantity accuracy)
  • Pin wrench (for oil screen service)

Step-by-Step Oil Change Procedure

  • Warm Up the Engine: Start and run the motorcycle for 2-3 minutes. This allows the oil to thin out and makes it drain more thoroughly (important for complete drainage) .
  • Position the Bike: Turn off the engine and place the FC250 on a stable, level surface or a bike stand. Ensure safety and stability throughout the procedure .
  • Remove Skid Plate (if equipped): Loosen any bolts or fasteners holding the skid plate, and remove it for access to the engine's underside.
  • Place the Drain Pan: Position your drain pan directly under the oil drain bolt.
  • Remove Oil Drain Bolt: Use your 13mm socket or wrench to remove the oil drain bolt. Allow the engine to completely drain. Inspect the old oil for any metallic particles—small amounts are typical, but chunks could signal a problem .
  • Remove Oil Screen Plugs and Oil Screens:
    • Your 2019 FC250 uses two oil screens that must be removed for thorough oil evacuation.
    • Remove the screws or plugs covering each oil screen. Carefully extract each screen using pliers or a pick. Note their orientation.
    • Clean the oil screens thoroughly with contact cleaner and inspect for debris or metal shavings .
  • Replace Crush Washer: Remove and replace the crush washer on the drain bolt if worn. Using a fresh washer prevents leaks.
  • Reinstall Oil Screens and Drain Bolt:
    • Reinstall the clean oil screens, ensuring proper orientation.
    • Reinstall the drain bolt and screen plugs. Tighten to specification (check the factory service manual for exact torque values). Do not overtighten .
  • Replace Oil Filter:
    • Remove the oil filter cover and old oil filter.
    • Lightly oil the gasket of the new filter and install it.
    • Reinstall the filter cover and torque the bolts to spec.
  • Add Fresh Oil:
    • Open the oil fill cap and add the specified quantity of fresh oil. For the 2019 FC250, use approximately 950 ml to 1 liter, but always check your manual to confirm capacity (usually about 1,000 ml, but verify before you pour) .
    • Use a measuring cup for accuracy.
  • Run and Recheck Oil Level:
    • Start the bike and let it idle for about 3 minutes to circulate new oil through the engine and filter .
    • Turn off the engine and allow oil to settle for a few minutes.
    • Check the oil level via the sight glass. Oil should be roughly halfway to three-quarters up the window. Top off if needed, but do not overfill .
  • Reinstall Skid Plate (if equipped): Secure it firmly before riding.
  • Dispose of Old Oil and Filter Properly: Take used oil and filter to a recycling center or auto parts store that accepts reclaimed oil.

Important Model-Specific Notes for the 2019 FC250 Rockstar Edition

  • Oil Change Interval: Husqvarna recommends changing the oil at minimum every 15 hours of operation, or sooner if the bike is raced or ridden hard. Many owners prefer every 5–10 hours for optimal engine health .
  • Oil Screen Maintenance: Always inspect the oil screens for debris or chunky metallic particles. Small amounts of paste-like shavings or micro particles are common, but large pieces may indicate a problem .
  • Torque Specs: Always refer to your owner's manual for the correct torque specification for the drain bolt, screen plugs, and filter cover. Over-tightening may strip threads in the magnesium case.
  • Filter Oiling: Prime the new oil filter with a bit of fresh oil before installing for best lubrication at startup .

Quick Reference: Oil Change Specifications (2019 FC250 Rockstar Edition)

  • Engine Oil Quantity: ~950 ml – 1,000 ml (check manual for official specification)
  • Oil Type: SAE 10W-50 (full synthetic recommended; always match specs in service manual)
  • Drain Bolt Torque: Refer to factory manual (typically 15 Nm, but verify for your bike)
  • Service Interval: Every 10–15 hours; shorten interval for racing or harsh conditions

By following these steps, your 2019 Husqvarna FC250 Rockstar Edition will remain properly lubricated and protected for many more hours of high-performance riding. Trust MotoSport.com for all your parts, tools, and maintenance advice.

Related Shopping Categories

Shop Motor Oil for a 2019 Husqvarna FC250 ROCKSTAR EDITION Dirt Bike.

Shop Oil Filters for a 2019 Husqvarna FC250 ROCKSTAR EDITION Dirt Bike.

Shop Oil Drain Pans for a 2019 Husqvarna FC250 ROCKSTAR EDITION Dirt Bike.

Shop Tools for a 2019 Husqvarna FC250 ROCKSTAR EDITION Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2019 Husqvarna FC250 ROCKSTAR EDITION Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.