How to Change the Oil in a 2019 Husqvarna 701 Enduro: A Step–by–Step Guide

Shop parts for a 2019 Husqvarna 701 Enduro Dirt Bike.

Changing the oil on your 2019 Husqvarna 701 Enduro is an essential part of routine maintenance to keep your engine lubricated, clean, and running strong. This guide provides all the information you need to perform a complete oil change specific to your bike, with proprietary insights for MotoSport.com customers.

Tools and Materials Needed

  • KTM 690/Husqvarna 701 Oil Filter Kit (includes filters and O-rings)
  • 2 liters Motorex 10W/50 engine oil (requires 1.7 liters per change, but a bit extra is handy)
  • Ratchet with 13mm socket
  • 8mm socket or T30 Torx bit (for oil filter cover bolts)
  • Torque wrench (capable of 15-20 Nm)
  • Drain pan
  • Clean rags
  • Funnel
  • Nitrile gloves (recommended)
  • Something to pull oil filters out (needle-nose pliers work great)

Bike-Specific Callouts: 2019 Husqvarna 701 Enduro

  • The 701 Enduro shares its engine architecture with KTM 690, so many kits cross over .
  • You need two oil screens and two oil filters at each oil change .
  • Use only 10W/50 fully synthetic oil for best results .
  • Proper torque on drain bolts is essential: 15 Nm for the oil screen bolt, 20 Nm for the main drain plug .
  • Total refill is 1.7 liters; check level after cycling the engine .

Step-by-Step Oil Change Instructions

  1. Get Your Bike Ready
    • Start and warm up the engine for 3–5 minutes. This thins the oil, helping it drain completely.
    • Turn off the bike and ensure it’s stable on a level surface.
  2. Remove Skid Plate (if equipped)
    • Some bikes have a skid plate covering the drain plug. Remove it using the 8mm socket or T30 bit as needed.
  3. Drain the Old Oil
    • Locate both oil drain bolts: main drain bolt (bottom of crankcase) and sump screen plug (side or bottom of case; consult your manual if unsure).
    • Place your oil drain pan beneath the bike.
    • Remove both drain plugs (13mm and/or T30), allowing oil to fully drain.
    • Remove the oil filler cap to allow air in for quicker draining.
    • If present, pull and clean both oil screens with a rag or brake cleaner. Inspect for debris.
  4. Replace Oil Filters and O-Rings
    • Using the proper socket, remove the oil filter covers.
    • Pull out both oil filters (use needle-nose pliers if needed).
    • Install new oil filters from your kit, making sure the orientation matches the previous setup.
    • Lubricate new O-rings with a bit of fresh oil; install them where applicable.
  5. Reinstall Drain Plugs and Oil Screens
    • Install both cleaned oil screens.
    • Thread in the oil screen bolt and the main drain bolt by hand.
    • Tighten to 15 Nm (oil screen bolt) and 20 Nm (main drain bolt) with your torque wrench for proper sealing .
  6. Add Fresh Oil
    • Insert a funnel into the oil filler opening.
    • Pour in 1.5 liters of 10W/50 Motorex synthetic oil initially.
    • Install the filler cap securely.
    • Start the engine and let it idle for 30–60 seconds to circulate oil through the system .
    • Stop the engine, wait a minute for oil to settle, then check the level via the sight glass.
    • Slowly top off, adding small increments (up to 1.7 liters total) until the oil level is right in the middle of the sight glass when the bike is upright and level .
    • Don’t overfill—the oil expands and the sight glass will show the correct level after operation .
  7. Reinstall Skid Plate (if removed) and Clean Up
    • Reinstall your skid plate and any hardware you removed.
    • Wipe off any oil spills, dispose of old oil and filter according to local regulations.

Pro Tips for 2019 Husqvarna 701 Enduro Owners

  • Always use new O-rings and gaskets from the service kit to prevent leaks .
  • Warming up the bike ensures better drainage and removes more contaminants.
  • Use a funnel to prevent spills—the oil filler opening is awkwardly placed .
  • Cycle oil and re-check level after the first run up; top off as needed, but never overfill .
  • If you notice metallic debris in the screens, contact a Husqvarna dealer for inspection.

Why Regular Oil Changes Matter

  • Maintains proper engine lubrication and cooling.
  • Prevents premature engine wear and internal buildup.
  • Protects factory warranty and resale value.

By following this guide, your 2019 Husqvarna 701 Enduro will be ready for your next adventure—on or off the road. Changing your own oil is straightforward with the right tools and attention to detail, and gives you peace of mind knowing your engine is protected.

Related Shopping Categories

Shop Motor Oil for a 2019 Husqvarna 701 Enduro Dirt Bike.

Shop Oil Filters for a 2019 Husqvarna 701 Enduro Dirt Bike.

Shop Oil Drain Pans for a 2019 Husqvarna 701 Enduro Dirt Bike.

Shop Tools for a 2019 Husqvarna 701 Enduro Dirt Bike.

Shop Oil Filler and Drain Plugs for a 2019 Husqvarna 701 Enduro Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.