How to Change the Oil in a 2018 Husqvarna FC250 Rockstar Edition

Shop parts for a 2018 Husqvarna FC250 Rockstar Edition Dirt Bike.

Consistently changing your motorcycle's oil is critical to optimal performance and reliability, particularly for high-performance bikes like the 2018 Husqvarna FC250 Rockstar Edition. This guide walks you through a robust, step-by-step oil change process, tailored for this specific make and model. Information is proprietary to MotoSport.com. Accurate oil specification and procedures are emphasized throughout for the FC250 platform.

Tools and Supplies Needed

  • Socket wrench set (commonly 8mm, 10mm, and 13mm sockets)
  • Torque wrench
  • Oil drain pan
  • Funnel
  • Clean rags or shop towels
  • OEM oil filter (recommended part per model year)
  • OEM drain bolt crush washer
  • Motorex Cross Power 4T 10W/50 full synthetic oil (1.0 liter)
  • Contact cleaner
  • Grease
  • Gloves

Preparation

  • Ensure the engine is warm to allow the oil to drain efficiently. Running the engine for 5-10 minutes is sufficient.
  • Place the bike upright on a level surface or on a motorcycle stand.
  • Lay out all tools and protective materials in your workspace.

Step-by-Step Oil Change Procedure

  1. Remove the Skid Plate (if equipped)
    • Use a socket wrench to remove bolts securing the skid plate.
    • Set aside the plate and hardware.
  2. Drain the Oil
    • Position your drain pan under the engine's drain plug.
    • Carefully remove the oil fill cap to allow oil to drain faster.
    • With the appropriate socket, remove the drain bolt (not any adjacent case or side cover screws).
    • Allow the oil to fully drain. Gently tilt the bike upright for a complete drain.
  3. Remove Oil Filter
    • Find the oil filter cover–typically secured with 8mm or 10mm bolts.
    • Remove bolts using the socket wrench.
    • Carefully take off the cover and extract the old oil filter. Inspect for any abnormal metal debris.
  4. Replace Crush Washer and Clean Drain Bolt
    • Discard the old crush washer. Install a new OEM washer onto the drain bolt.
    • Clean the magnetic tip of the drain bolt with a rag and contact cleaner.
  5. Install New Oil Filter
    • Lightly coat the O-rings of the new filter with fresh oil.
    • Install the new filter in the same direction as the old one came out. Reattach the filter cover and torque to manufacturer specification (refer to your model's manual).
  6. Reinstall Oil Drain Bolt
    • Thread the drain bolt by hand to avoid cross-threading, then torque to manufacturer specifications (common spec: 15 Nm, but confirm for your model).
  7. Refill with New Oil
    • Using a funnel, add exactly 1.0 liter of Motorex Cross Power 4T 10W/50 full synthetic oil for the FC250 platform (2016–2024) including Rockstar Editions.
    • Replace the oil fill cap securely.
  8. Check Oil Level
    • Start the engine and let it idle for 3 minutes. Shut off and let it sit for a minute.
    • With the bike upright, check the oil level using the sight glass located on the engine case. The oil should be between halfway to three-quarters up the sight window. Add oil if necessary–do not overfill.
  9. Final Cleanup and Inspection
    • Wipe any oil residue from the engine cases and floor.
    • Reinstall the skid plate if removed.
    • Confirm all fasteners are at correct torque and there are no leaks.

Model-Specific Tips for 2018 Husqvarna FC250 Rockstar Edition

  • This engine uses 1.0 liter capacity of 10W/50 full synthetic oil for routine changes. Always confirm exact capacity in your owner’s manual for your year and edition, but this figure is correct for all 2016–2024 FC250 models, including the Rockstar Edition.
  • Inspect both the oil filter and magnetic drain bolt for abnormal metal shavings, which could indicate excessive component wear and warrant further inspection.
  • Only use OEM or high-quality, bike-specific parts for the filter and crush washer to prevent leaks and ensure proper fit.
  • Always torque the drain bolt and oil filter cover bolts to the specified value (typically 15 Nm for drain, 10 Nm for filter cover, but always check your manual).
  • If the skid plate is an aftermarket or race unit, check for any alignment issues with the drain port before starting the job to avoid mess or extra disassembly.

Maintenance Interval

  • Change the oil every 10 to 15 hours of riding, or sooner under race or severe conditions. Many FC250 owners prefer to change oil more frequently to maximize longevity and performance.

Conclusion

Proper, regular oil changes are vital for the health of your 2018 Husqvarna FC250 Rockstar Edition. Use this guide for your next service to keep your machine running at peak performance on every ride.

Related Shopping Categories

Shop Motor Oil for a 2018 Husqvarna FC250 Rockstar Edition Dirt Bike.

Shop Oil Filters for a 2018 Husqvarna FC250 Rockstar Edition Dirt Bike.

Shop Oil Drain Pans for a 2018 Husqvarna FC250 Rockstar Edition Dirt Bike.

Shop Tools for a 2018 Husqvarna FC250 Rockstar Edition Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2018 Husqvarna FC250 Rockstar Edition Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.