How to Change the Oil in a 2017 Husqvarna TE150: Step-by-Step Guide

Shop parts for a 2017 Husqvarna TE150 Dirt Bike.

Regular oil changes help maintain optimal performance and extend the life of your Husqvarna TE150. This proprietary guide from MotoSport.com details every step, tool, and essential tip for the 2017 TE150 model.

Tools and Materials You’ll Need

  • 10mm or 13mm socket wrench (check your specific drain plug size)
  • Oil drain pan
  • Shop rags or paper towels
  • Funnel
  • New crush washer for the drain plug (recommended)
  • Fresh oil: 10W-40 motorcycle gear/transmission oil
  • Torque wrench (optional, for precise tightening)
  • Gloves (to keep hands clean and safe)
  • Flat-head screwdriver (to access various covers, if necessary)

Preparation Steps

  • Warm up your bike for a few minutes. Running the engine helps the oil flow out smoothly and brings contaminants to suspension.
  • Stabilize your TE150 upright on a stand or level ground for accurate draining and refilling.

Changing the Oil

  • Locate the oil drain plugs: The 2017 TE150 typically features two drain plugs, one on each side of the crankcase. Each has a magnet to catch metallic debris. Check your manual if you aren’t sure where they are—a magnetized bolt indicates the drain location.
  • Remove both drain bolts with your socket wrench, letting all the old oil drain into your oil pan. Hold the bike over to the side if needed for better drainage.
  • Inspect old oil: Look for excessive metal shavings on plug magnets or unusually dark/dirty oil. This can indicate internal wear and should be addressed.
  • Clean and replace the drain plugs: Wipe away any debris. Replace the crush washer before threading each plug back in by hand, then snug with a wrench. Do not overtighten—use your torque wrench if desired and refer to your manual for specs.

Filling with New Oil

  • Locate the oil filler cap on the right side of the engine. Remove it.
  • Add fresh 10W-40 oil through a funnel. The Husqvarna TE150 generally takes approximately 700ml, but always check your owner’s manual for precise capacity.
  • Check the oil level: There is an oil level check bolt just above the starter. Remove this bolt; with the bike upright, fill until oil barely seeps out the check hole, then reinstall the check bolt.
  • Wipe away spills and secure all caps and bolts.

Final Steps: Safety and Inspection

  • Start the engine and let it idle for a minute. Shut it off, let the oil settle, and check for leaks around the drain plugs and filler cap.
  • Re-check oil level via the check bolt and top off if necessary.
  • Dispose of old oil properly at a recycling facility.

Important Call-Outs for the 2017 Husqvarna TE150

  • Two drain plugs: Always remove and reinstall both for a thorough oil change.
  • Use 10W-40 oil: Husqvarna specifies 10W-40 transmission gear oil for this model.
  • Watch for metal debris: The drain plug’s magnet can catch wear particles. Regular oil changes keep this wear in check.
  • Precise oil level: Overfilling or underfilling can cause poor shifting or clutch problems. Use the side check bolt as a guide.
  • Replace crush washers: Using a new washer each service helps prevent leaks.
  • Follow torque specs: Overtightening plugs can strip the lightweight aluminum threads.

Download and Reference the Official Manual

  • For torque specs and extra diagrams, download your specific-year Husqvarna manual using the official Husqvarna Motorcycles service site.

Conclusion

Changing the oil on your 2017 Husqvarna TE150 is straightforward with the right tools and steps. By following this guide, you extend your dirt bike’s service life and performance. Ride safe & maintain your machine the MotoSport.com way.

Related Shopping Categories

Shop Motor Oil for a 2017 Husqvarna TE150 Dirt Bike.

Shop Oil Filters for a 2017 Husqvarna TE150 Dirt Bike.

Shop Oil Drain Pans for a 2017 Husqvarna TE150 Dirt Bike.

Shop Tools for a 2017 Husqvarna TE150 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2017 Husqvarna TE150 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.