How to Change the Oil in a 2017 Husqvarna FC250 – MotoSport.com Guide

Shop parts for a 2017 Husqvarna FC250 Dirt Bike.

Keeping the oil fresh in your 2017 Husqvarna FC250 is crucial for optimal performance and longevity. Here’s a comprehensive, proprietary guide—built exclusively for MotoSport.com—on safely and effectively changing the oil, including tools, model-specific tips, and safety precautions.

Tools & Supplies Needed

  • 8mm and 13mm sockets or wrenches
  • Pin wrench for oil screens (as recommended by Husqvarna)
  • Drain pan (large enough for at least 1.1L of oil)
  • New oil filter (specific for the 2017 FC250)
  • Replacement engine oil (refer to manual for grade and 1.1 liter capacity)
  • New crush washer/seal ring (recommended with every oil change)
  • Clean rags/paper towels
  • Contact cleaner (optional, for cleaning any spilled oil)
  • Torque wrench (optional but highly recommended)
  • Measuring cup (to refill the right amount of oil)
  • Nitrile gloves (for cleaner hands and safety)

Preparation Steps

  • Warm up your engine for a few minutes, then shut it off. Warm oil drains more thoroughly and carries away more debris

    .
  • Place the bike on a level surface using a stand, and ensure it is stable

    .
  • Gather all your tools and supplies within reach.

Step-by-Step Process to Change Oil in a 2017 Husqvarna FC250

  1. Remove the Oil Drain Plug
    • Identify the main oil drain plug under the engine (look for the magnetic plug; residue on it is normal)

      .
    • Use an appropriate socket/wrench (usually 13mm) to loosen and remove the plug; let the oil drain completely into the catch pan

      .
    • Safety Tip: Oil can be hot—avoid burns by using gloves and waiting a bit after shutting off the engine

      .
  2. Remove and Clean Oil Screen
    • Locate and remove the oil screen plug using a pin wrench

      . (On the FC250, it is on the side of the engine; consult your manual for precise location.)
    • Pull out the oil screen—check for debris or metallic fragments and clean thoroughly.
    • Wipe down the screen and its seating area. Reinstall the cleaned screen using its O-ring and pin wrench. Ensure the O-ring is in good condition—replace if necessary

      .
  3. Replace Oil Filter
    • Locate the oil filter cover (usually held by two bolts, 8mm or 10mm)

      .
    • Remove the cover and slide out the old oil filter.
    • Prime the new oil filter with a little fresh oil, then install it into the housing. Ensure rubber O-rings remain on the cover and are in good condition.
    • Tighten the oil filter cover bolts snugly (do not overtighten).
  4. Reinstall Drain Plug and Oil Screen Plug
    • Install a new crush washer/seal ring on the oil drain plug for leak prevention

      .
    • Hand-thread the drain plug and oil screen plug, then use a torque wrench to tighten to factory spec (consult your owner's manual for specifics—over-tightening can strip the case

      ).
  5. Add Fresh Oil
    • Pour in the specified volume (about 1.1L; check the manual) of the recommended oil grade for your FC250

      .
  6. Check Oil Level
    • Start the motorcycle and let it idle for one minute, then shut it off and wait another minute

      .
    • Check the oil sight glass—the oil should be between the middle and the top of the viewer. Add small amounts if needed to bring the level up.
  7. Final Inspection
    • Check for any leaks around the oil drain, oil filter, and oil screen areas.
    • Wipe down any spilled oil.

2017 Husqvarna FC250 Model-Specific Tips

  • The magnetic drain plug on this model is designed to catch metallic particles. Clean it thoroughly before reinstalling

    .
  • The oil screen should not have excessive debris. Minor residue is normal, but lots of metal fragments or sludge could indicate engine issues

    .
  • Always use a fresh crush washer to prevent leaks

    .
  • Torque settings vary—always follow specs in your owner’s manual for plug and filter bolts

    .
  • Oil changes should be performed every 15 hours of riding or sooner in extreme conditions

    .

Safety and Environmental Notes

  • Never dump used oil down the drain or on the ground. Take it to a recycling center or designated drop-off.
  • Always allow the motorcycle and oil to cool before working, especially if you’re new to wrenching.

Conclusion

Changing the oil in your 2017 Husqvarna FC250 is straightforward when you follow the steps and use the right tools. Sticking to routine oil changes and proper techniques will keep your dirt bike running at its best—ride on.

Related Shopping Categories

Shop Motor Oil for a 2017 Husqvarna FC250 Dirt Bike.

Shop Oil Filters for a 2017 Husqvarna FC250 Dirt Bike.

Shop Oil Drain Pans for a 2017 Husqvarna FC250 Dirt Bike.

Shop Tools for a 2017 Husqvarna FC250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2017 Husqvarna FC250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.