How to Change the Oil in a 2017 Husqvarna 701 Enduro
Shop parts for a 2017 Husqvarna 701 Enduro Dirt Bike.
Changing the oil regularly keeps your 2017 Husqvarna 701 Enduro running strong and helps prevent costly repairs down the road. This comprehensive guide details all the tools required, walks you through step-by-step instructions, and highlights the critical details specific to the 2017 701 Enduro. Proudly brought to you by MotoSport.com.
Tools & Supplies Needed
- Socket set and ratchet (including 8mm, 13mm, and Torx bits as required)
- Oil catch pan
- Motorex Power Synthetic 4T 10W/50 engine oil (or equivalent SAE 10W-50 JASO MA2 spec)
- New oil filters (part number 58038005100 or Hiflofiltro HF155)
- Funnel
- Replacement O-rings/crush washers (replace as needed–copper washer for drain plug recommended)
- Contact or brake cleaner (for cleaning drain plugs and oil screens)
- Torque wrench
- Clean shop rags
- Flathead screwdriver or pick (for removing oil screens, if needed)
- Gloves and safety goggles
Oil Quantity – Service Interval
- Oil capacity: 1.7 liters (1.8 US quarts)
- Recommended oil: Full synthetic 10W-50 (Motorex Power Synthetic 4T 10W/50 or equivalent)
- Service interval: Every 10,000 km (6,200 miles) or annually, whichever comes first
Step-By-Step Instructions
-
Prepare the bike:
- Warm up the engine for several minutes. Warm oil drains more completely and suspends contaminants better.
- Turn off the bike, place it on a stable surface (using a center or paddock stand), and let cool slightly.
-
Remove the skid plate (if equipped):
- Use the correct size socket or Torx bit to remove the skid plate for easy oil drain plug access.
-
Drain the old oil:
- Place your oil catch pan under the engine—s main sump plug (on the bottom left side).
- Remove the main drain plug using a 13mm socket, allow oil to drain fully.
- Remove the secondary drain plugs (front of engine and lower case, depending on model year revision) to allow complete oil flow.
-
Clean and inspect:
- Clean the magnetic drain plugs with contact cleaner to remove any metal debris.
- Check copper or aluminum crush washers–replace if damaged or excessively compressed.
-
Remove and clean oil screens:
- Remove the oil screen plugs (with a socket or Allen bit) at the front and side of the engine.
- Extract the oil screens, clean thoroughly with contact cleaner, and inspect for debris or damage.
- If needed, replace with new oil screens for maximum protection.
-
Remove and replace oil filters (two locations):
- The 701 Enduro has two oil filters–one is on the left under the exhaust header, the other on the right case cover.
- Remove the oil filter covers (8mm socket), carefully extract each filter, and clean the cover sealing areas.
- Install new (or thoroughly cleaned) oil filters. Lubricate the new O-rings before installation.
- Torque the filter cover bolts to specification.
-
Reinstall drain plugs and oil screens:
- Fit cleaned screens back into their ports, install drain plugs and torque all to factory spec (consult your service manual for accurate torque values).
- Do not over-tighten–strip threads are a frequent issue on soft engine cases.
-
Add fresh oil:
- Remove the oil fill cap, insert your funnel, and pour in around 1.5 liters of new oil to start.
- Reinstall fill cap. Start the engine and let it idle for 20–30 seconds—this distributes new oil through the system.
- Shut off engine; wait a minute for the oil to settle, then check sight glass (right side of engine cover).
- Add remaining oil as needed–aiming for 1.7 liters total until oil is near the upper mark but not overfilled.
-
Final checks and clean-up:
- Inspect for leaks around all plugs, filters, and screens.
- Reinstall the skid plate if removed.
- Wipe off any spilled oil, responsibly recycle old oil at a local disposal center, and record your service for the maintenance log.
2017 Husqvarna 701 Enduro – Special Notes & Model-Specific Callouts
- Dual Oil Filters & Screens: Unique to engines in the KTM 690/Husqvarna 701 family, ensure both filters and both screens are serviced every oil change to maintain engine health.
- Magnetic Drain Plugs: Check for excessive metal shavings—signs of abnormal wear.
- Oil Capacity: Always confirm oil level using the sight glass after running the engine; do not rely solely on quantity added.
- Torque Specs: Always use a torque wrench. These engines have soft aluminum threads that can be damaged by over-tightening.
- Recommend Oil: Husqvarna specifies Motorex Power Synthetic 4T 10W/50; using another, ensure it matches JASO MA2 rating for wet clutch compatibility.
- Engine Guard Note: If your bike has aftermarket protection or crashbars, you may need to remove these for oil plug/filter access.
- Service Interval: Adhere to the 10,000 km or annual oil change schedule, or more often if you ride off-road frequently or in harsh conditions.
Why Regular Oil Changes Matter
- Fresh oil ensures proper lubrication, cooling, and protects engine internals from accelerated wear.
- Neglecting oil changes may cause clutch slippage, valve train wear, or catastrophic engine failure.
All content proprietary to MotoSport.com. For OEM parts, premium oils, and expert service supplies, always trust MotoSport for your Husqvarna 701 Enduro maintenance needs.
Related Shopping Categories
Shop Motor Oil for a 2017 Husqvarna 701 Enduro Dirt Bike.
Shop Oil Filters for a 2017 Husqvarna 701 Enduro Dirt Bike.
Shop Oil Drain Pans for a 2017 Husqvarna 701 Enduro Dirt Bike.
Shop Tools for a 2017 Husqvarna 701 Enduro Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2017 Husqvarna 701 Enduro Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.