How to Change the Oil in a 2016 Yamaha TTR110: A Complete Guide
Shop parts for a 2016 Yamaha TTR110 Dirt Bike.
This proprietary MotoSport.com guide walks you through changing the oil in a 2016 Yamaha TTR110–a simple task that greatly extends the life and performance of your dirt bike. These steps are specific to the TTR110 design, which shares its oil change procedure with models from prior and subsequent years due to their almost unchanged engine design.
Tools and Supplies Needed
- 12mm wrench or socket/ratchet
- Oil drain pan (catch can or suitable container)
- Narrow funnel
- Clean rag or shop towel
- Measuring cup or markings for oil volume
- Fresh oil: Yamaha recommends Yamalube 10W-40; you’ll need 0.85 quarts (27–28 ounces)
- Replacement crush washer (optional but recommended)
- Spray brake/contact cleaner (optional, for cleanup purposes)
Step-by-Step Oil Change Process
-
Warm Up the Engine
- Start your TTR110 and let it run for 5–10 minutes. This heats the oil, allowing it to drain more thoroughly and carry away more contaminants.
-
Place the Bike Securely
- Set the bike upright on a level surface. If possible, use a bike stand.
-
Remove the Oil Fill Cap
- Unscrew the oil filler cap/dipstick on the right side of the engine to allow air in for smoother drainage.
-
Locate and Remove the Drain Bolt
- The drain bolt (12mm head) is located on the bottom of the engine. Position your oil pan directly underneath.
- Using your 12mm wrench or socket, carefully remove the drain bolt. Be ready for a quick pour of hot oil–wear gloves if necessary.
- Set the bolt aside with its washer. Inspect the washer and replace it if damaged or crushed.
-
Let Oil Drain Completely
- Tilt the bike gently from side to side to help drain every bit of old oil.
- Wait several minutes for full drainage.
-
Reinstall Drain Bolt
- Clean the drain bolt and reinstall it with a new washer if necessary.
- Tighten the drain bolt securely but avoid over-tightening–this could strip the threads.
-
Pour In New Oil
- Set your funnel in the oil fill port. Carefully pour in 0.85 quarts (about 27-28 ounces) of 10W-40 Yamalube oil. Yamaha oil bottles have clear measurement markings for accuracy.
- Do not use automotive oils or any friction-modified oils–these may cause clutch slippage since the TTR110 uses a wet clutch design. Use only oil approved for wet-clutch motorcycles.
- Pro tip: Pour with the slant side of the bottle down for a smoother, spill-free fill.
-
Reinstall the Oil Filler Cap/Dipstick
- Check the cap’s O-ring for wear or damage. Replace it if necessary.
- Hand-tighten the cap only. Avoid using tools that could strip the threads.
-
Check Oil Level
- With the bike upright on a level surface, insert the dipstick (do not screw in) and check the oil level. Add a small amount if necessary, but do not overfill.
-
Clean Up
- Wipe away any spilled oil from the engine or frame using your rag and, if needed, a few spritzes of brake/contact cleaner.
-
Start the Engine and Final Check
- Start the engine and let it run for 2–3 minutes. Check for leaks at the drain bolt and the filler cap.
- Recheck oil level after the engine has run and cooled for a couple of minutes, topping off if required.
2016 Yamaha TTR110 Specific Call-Outs
- No oil filter: The TTR110 engine does not use a replaceable oil filter–so you are only draining and replacing the oil, making the procedure simpler and faster than many larger bikes.
- Oil Capacity: The engine calls for exactly 0.85 quarts (about 27–28 ounces) each oil change. Overfilling can affect performance and may cause leaks or clutch issues.
- Oil Type: Do not use car oil or products with “energy conserving” labels. Only use high-quality 10W-40 motorcycle oil to maintain clutch performance and engine longevity.
- Consistency Across Model Years: The oil change process and specs are essentially unchanged for Yamaha TTR110s roughly from 2011 onward, so procedures remain valid for neighboring years.
- Measurement Tip: The Yamalube bottle comes with clear measurement markings in ounces and milliliters for precision.
- Crush Washer: It’s a best practice to replace the drain bolt washer every oil change to minimize the risk of leaks.
Properly disposing of old oil: Take the used oil to a local auto parts store or recycling center–never dump oil in the ground or drains.
Changing the oil in your 2016 Yamaha TTR110 is a quick and rewarding task, helping you keep your bike running at its best for years to come.
For more dirt bike maintenance guides and genuine parts, visit MotoSport.com—your professional source for everything off-road.
Related Shopping Categories
Shop Motor Oil for a 2016 Yamaha TTR110 Dirt Bike.
Shop Oil Filters for a 2016 Yamaha TTR110 Dirt Bike.
Shop Oil Drain Pans for a 2016 Yamaha TTR110 Dirt Bike.
Shop Tools for a 2016 Yamaha TTR110 Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2016 Yamaha TTR110 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.