How to Change the Oil in a 2016 Husqvarna TE125

Shop parts for a 2016 Husqvarna TE125 Dirt Bike.

Changing the oil in your 2016 Husqvarna TE125 is one of the most important maintenance tasks for ensuring longevity and peak performance of your bike. This step-by-step MotoSport.com exclusive guide details the entire process, lists the tools you'll need, and provides model-specific tips for the TE125. Always refer to your owner's manual for further reference.

Tools & Supplies Needed

  • Socket wrench set (8mm and 13mm sockets recommended)
  • Oil drain pan
  • Funnel
  • Clean rags or paper towels
  • New gear oil–Husqvarna recommends 10W-40 gear oil, 650ml capacity for the TE125
  • Replacement oil drain plug gasket or washer
  • Rubber gloves (optional but recommended)

Preparation

  • Always change the oil when the engine is warm, not hot.
    • This ensures the oil drains more freely and brings out more impurities.
  • Make sure the bike is upright and on a stand before you start.
  • Clean the area around the drain plug to prevent debris from entering the engine.

Steps to Change the Oil

  1. Warm Up the Engine
    • Start your TE125 and let it run for a few minutes. Shut off the engine and allow it to cool for a moment, so it's comfortable to handle, but oil is still warm and viscous.
  2. Locate the Oil Drain Plug
    • The TE125's oil drain plug is on the bottom of the engine case, generally easy to spot underneath the skid plate. You may want to remove the skid plate, if equipped, for better access.
    • Ensure you are using the correct plug–refer to your manual if needed for exact location. Note: The oil fill cap is located on the right side of the engine, above the clutch cover.
  3. Drain the Old Oil
    • Place the drain pan beneath the drain plug.
    • Use your socket wrench to remove the drain bolt. Allow all the old oil to flow out–tilt the bike gently side to side to ensure thorough drainage.
    • Inspect the drain plug and washer for wear or damage. Replace the washer if necessary to prevent leaks.
    • Wipe away any oil residue from the case and threads.
  4. Replace the Drain Plug
    • After oil has drained completely (wait a few extra minutes for a full drain), reinstall the drain plug and gasket/washer.
    • Tighten to manufacturer's recommended torque spec–overtightening can strip threads or crack the case.
  5. Refill with New Oil
    • Remove the oil fill cap from the right side of the engine.
    • Insert a clean funnel and pour in the recommended amount of fresh 10W-40 gear oil–650 ml for the TE125. It's crucial not to overfill as this can cause excess pressure or leaks.
    • Replace and tighten the oil fill cap securely.
  6. Check for Leaks
    • Wipe down the drain plug area and start your engine for one to two minutes. Check around the drain plug and oil filter for leaks.
    • Shut off the engine, allow it to settle, then inspect oil level through the sight glass or fill plug as per your owner's manual. Top off if necessary.

2016 Husqvarna TE125 Model-Specific Tips

  • Oil Capacity:
    • The 2016 TE125 requires 650 ml gear oil.
  • Drain Plug Torque:
    • Check your Husqvarna service manual for the torque specification to avoid stripping threads–use a torque wrench if possible.
  • Drain Plug Location:
    • This model uses the same plug from 2011-2016, making replacement straightforward if needed. Premium steel replacements are available for extra longevity.
  • Oil Change Interval:
    • Husqvarna recommends changing the gear oil regularly–intervals depend on riding conditions but generally after every 10 hours of use or every 2–3 races for high-performance riding.
  • Gear Oil Type:
    • Only use oil approved for wet-clutch use to ensure proper clutch function and gearbox protection.

Final Notes

  • Dispose of your old oil responsibly–take it to an approved recycling facility or hazardous waste location.
  • Always use gloves and clean your tools thoroughly after each service.
  • Record your oil changes and note riding conditions to monitor engine health and maintenance intervals.

This custom guide is brought to you by MotoSport.com—your trusted source for dirt bike parts, gear, and service guides. By following these steps and observing the specific requirements for the 2016 Husqvarna TE125, you'll keep your bike performing at its best for many rides to come.

Related Shopping Categories

Shop Motor Oil for a 2016 Husqvarna TE125 Dirt Bike.

Shop Oil Filters for a 2016 Husqvarna TE125 Dirt Bike.

Shop Oil Drain Pans for a 2016 Husqvarna TE125 Dirt Bike.

Shop Tools for a 2016 Husqvarna TE125 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2016 Husqvarna TE125 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.