How to Change the Oil in a 2016 Husqvarna FC250

Shop parts for a 2016 Husqvarna FC250 Dirt Bike.

Keeping your 2016 Husqvarna FC250 in top condition means ensuring regular oil changes. Fresh oil is critical for the engine's longevity and maximum performance. This step-by-step MotoSport.com exclusive guide walks you through the full oil change process, highlights the specific tools you'll need, and notes important tips unique to the 2016 FC250 model.

Tools and Supplies Needed

  • 1.0 liter Motorex Cross Power 4T 10W/50 full synthetic oil (or equivalent)
  • OEM oil filter (specific to Husqvarna FC250/350, part included in oil change kits)
  • Oil drain bolt crush washer (included in most kits)
  • Drain pan for catching used oil
  • 13mm socket or wrench
  • Pin wrench for oil screen removal
  • Measuring pitcher (for precise refilling)
  • Contact cleaner (for cleanup)
  • Torque wrench
  • Paper towels or clean rags
  • Nitrile/latex gloves (recommended for clean hands)

Preparatory Steps

  • Warm up the engine:– Let the bike idle for a few minutes. Warm oil drains more efficiently, removing more contaminants and debris from the motor.
  • Turn off and secure the bike:– Park your Husqvarna FC250 on a level surface. Use the bike stand to keep it upright and secure.
  • Gather all tools and supplies:– Having everything ready before you start will make the process faster and minimize mess.

Step-by-Step Oil Change Process

  • Place the drain pan:– Slide your oil drain pan under the engine to catch the draining oil.
  • Remove the oil drain bolt:–
    • Using a 13mm socket or wrench, carefully remove the oil drain bolt on the bottom of the engine. Caution: Oil will be hot.
    • Let the oil fully drain. Watch for the crush washer–it should be replaced every oil change for a proper seal.
  • Remove the oil screen:–
    • Locate the oil screen access plug. Using a pin wrench, remove the plug and gently pull out the oil screen.
    • Inspect the screen for debris or metal shavings. Clean it thoroughly using contact cleaner and a lint-free rag.
    • Reinstall the screen and torque the plug to manual specification (consult your manual for exact values).
  • Remove the oil filter:–
    • Find and remove the oil filter cover bolts. Take off the cover and remove the old oil filter.
    • Allow any excess oil to fully drip out. Clean the filter housing with a rag.
  • Install the new oil filter:–
    • Lightly oil the seal of the new oil filter. Place the new filter into position.
    • Reinstall the cover and tighten the bolts evenly to avoid leaks. Torque to specification.
  • Replace the drain bolt and crush washer:–
    • Install a new crush washer on the drain bolt, thread the bolt in by hand, then torque it to the spec found in your owner's manual. Overtightening can strip the threads in the crankcase.
  • Refill with fresh oil:–
    • Remove the oil fill cap. Pour in exactly 1.0 liter of Motorex Cross Power 4T 10W/50 or your preferred equivalent, using a measuring pitcher for precision.
    • Replace the oil fill cap.
  • Check for leaks and oil level:–
    • Start the engine (don't rev). Let it idle for 30 seconds, then shut off and check for leaks around the drain bolt and oil filter area.
    • After a minute, check the oil level window or dipstick (if equipped) and top off if necessary.
  • Dispose of old oil properly:–
    • Take your used oil to a certified recycling location. Never dispose of engine oil in the trash or down drains.

2016 Husqvarna FC250-Specific Tips and Call-Outs

  • Always use a new crush washer:– The FC250 uses an aluminum or copper crush washer that should be replaced every oil change for a proper seal and to avoid leaks.
  • Torque is critical:– The small threads for the drain and oil screen plugs can strip easily. Use a torque wrench and refer to your owner's manual for exact specs.
  • Oil capacity:– Use precisely 1.0 liter of oil for the 2016 FC250 (not more, unless stated differently in your manual).
  • Inspect removed oil and screen:– Always check for metallic debris; excessive fragments may indicate a possible engine issue and should prompt further investigation before continued riding.
  • Synthetic oil use:– Husqvarna recommends full synthetic oil, such as Motorex Cross Power 4T 10W/50, especially for high-performance four-stroke engines like the FC250.
  • Compatible years:– The oil change kit and process are consistent for Husqvarna FC250 models from 2016–2024 and carry over to several related models (see kit packaging for full compatibility)

Final Thoughts

Changing your 2016 Husqvarna FC250's oil is straightforward with the right tools and attention to detail. Stick to the service intervals and always use OEM or premium-quality oil and filters for the best protection and performance. For further technical support or OEM Husqvarna parts, visit MotoSport.com or contact your nearest authorized Husqvarna dealer.

Ride safe, perform regular maintenance, and enjoy the trails with confidence.

Related Shopping Categories

Shop Motor Oil for a 2016 Husqvarna FC250 Dirt Bike.

Shop Oil Filters for a 2016 Husqvarna FC250 Dirt Bike.

Shop Oil Drain Pans for a 2016 Husqvarna FC250 Dirt Bike.

Shop Tools for a 2016 Husqvarna FC250 Dirt Bike.

Shop Oil Fillers and Drain Plugs for a 2016 Husqvarna FC250 Dirt Bike.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.