How to Change the Oil in a 2016 Husqvarna 701 Enduro: MotoSport.com Guide
Shop parts for a 2016 Husqvarna 701 Enduro Dirt Bike.
Keeping the oil fresh in your 2016 Husqvarna 701 Enduro is essential for engine health and longevity. This guide provides a step-by-step method, tools required, and call-outs specific to this model to ensure a successful oil change every time.
Tools and Supplies Needed
- Socket set (including 13mm deep socket)
- Torx wrench or Torx bits
- Flathead screwdriver (helpful for removing oil filter covers)
- Oil drain pan
- Torque wrench
- Clean rags or shop towels
- New oil filters (2)
- Replacement O-rings (if needed)
- New engine oil (1.7 liters recommended for 701 Enduro)
- Funnel
- Contact cleaner (for screen and plug cleaning)
- Protective gloves
Recommended Oil Type and Quantity
- Engine oil quantity:– 1.7 liters (approximately 1.8 quarts)
- Quality:– Full-synthetic motorcycle oil per manufacturer’s specification
Step-by-Step Oil Change for 2016 Husqvarna 701 Enduro
- Warm up the engine:– Run your bike for several minutes. This helps the old oil drain more thoroughly.
- Prepare your workspace:– Ensure the bike is on a stable, flat surface using the side or center stand. Lay down cardboard or rags to catch splashes.
- Remove the skid plate (if fitted):– Use the socket or Torx bits to remove the plate for easier access to drain bolts and screens.
-
Locate and remove drain plugs and oil screens:–
- You will find two drain bolts at the bottom and front of the engine. Use a 13mm deep socket to loosen and remove each bolt; allow the oil to drain into the pan.
- Beneath the drain plugs, look for the oil screens. Pull them out carefully. Clean them thoroughly with contact cleaner, or replace as needed. Make sure O-rings are undamaged and properly seated when reinstalling
-
Remove oil filter covers:–
- There are two oil filter covers–one on each side of the engine. Use a Torx wrench or bits to remove the bolts. Carefully pull the covers; you might need a flathead screwdriver to ease them off if they stick.
- Inspect and replace both oil filters. Lightly oil the new filters before installation.
- Inspect O-rings on the covers; replace if cracked or flattened.
- Reinstall oil screens and drain plugs:– Insert cleaned or new oil screens, then hand-thread the drain bolts and torque them to spec (front oil screen: 15 Nm; drain plug: 20 Nm) .
- Install new oil filters and tighten covers:– Install new or cleaned filters. Replace covers and tighten the Torx screws to the manufacturer's recommended settings.
-
Add new oil:–
- Using a funnel, pour in 1.7 liters of recommended synthetic oil.
- Replace oil filler cap.
-
Prime the oil system:–
- Start the engine and let it idle for a minute to circulate the new oil. Shut off the engine, check for leaks, and allow oil to settle.
-
Check oil level:–
- Confirm the bike is upright and on a level surface.
- Check the sight glass on the case; oil level should be between the minimum and maximum marks. Add small increments as needed–avoid overfilling.
- Reinstall skid plate (if removed):–
- Dispose of used oil and filters properly:– Take them to a recycling center or an auto parts shop that accepts used oil.
2016 Husqvarna 701 Enduro-Specific Call-Outs
- This bike uses two oil screens that should be cleaned or replaced every oil change; neglecting these can lead to oiling issues .
- Check O-rings on both oil screens and filter covers. Damaged O-rings are a common source of leaks.
- The two drain plugs and oil screens can be “tricky” to remove the first time–use patience and the right tool for the deep socket. Avoid using force or prying hard, which can damage plugs or threads .
- Recommended torque specs: oil screen bolt: 15 Nm; drain bolt: 20 Nm. Always use a calibrated torque wrench to avoid stripping threads .
- Oil quantity should not exceed 1.7 liters; overfilling may cause engine or breather issues .
- After the initial fill and the first engine run, top off with any remaining oil up to, but not past, the maximum on the sight glass .
Pro Tips for MotoSport.com Riders
- Always double-check for leftover tools or rags before starting the engine after servicing.
- Take your time cleaning screens and installing O-rings to avoid future leaks.
- Consider installing a magnetic drain plug to catch metal particles and further protect your engine.
With these steps and precautions, you can confidently service your Husqvarna 701 Enduro’s oil system and keep your ride in peak condition. For quick parts ordering and more how-to guides, visit MotoSport.com.
Related Shopping Categories
Shop Motor Oil for a 2016 Husqvarna 701 Enduro Dirt Bike.
Shop Oil Filters for a 2016 Husqvarna 701 Enduro Dirt Bike.
Shop Oil Drain Pans for a 2016 Husqvarna 701 Enduro Dirt Bike.
Shop Tools for a 2016 Husqvarna 701 Enduro Dirt Bike.
Shop Oil Fillers and Drain Plugs for a 2016 Husqvarna 701 Enduro Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.